A 915 mm diameter driving pulley is used to drive 1,220 mm pulley. The center to center distance between the two pulleys is 3.5 mm and the output of the driven shaft is 85 HP. If a leather belt is used with a belt speed of 1,300 m/min coefficient of friction is 0.28, percent slip is 1.5% on each pulley, and loss due to friction on each shaft is 6%, calculate: (a) The rpm of each shaft: Ans. N1 = 459.13 rpm; N2 = 344.35 rpm (b) Difference in belt tension: Ans.(F1 - F2) = 3.11 kN (c) Size of 9.5 mm thick leather belt: Ans. b = 0.2475 mm; L = 10.6792 m

A 915 mm diameter driving pulley is used to drive 1,220 mm pulley. The center to center distance between the two pulleys is 3.5 mm and the output of the driven shaft is 85 HP. If a leather belt is used with a belt speed of 1,300 m/min coefficient of friction is 0.28, percent slip is 1.5% on each pulley, and loss due to friction on each shaft is 6%, calculate: (a) The rpm of each shaft: Ans. N1 = 459.13 rpm; N2 = 344.35 rpm (b) Difference in belt tension: Ans.(F1 - F2) = 3.11 kN (c) Size of 9.5 mm thick leather belt: Ans. b = 0.2475 mm; L = 10.6792 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A flat belt with a width of 120 mm and a thickness of 5 mm transmits power from a driving pulley with a diameter of 250 mm to a driven pulley with a diameter of 700 mm. The mass per unit length of the belt is 2.1 kg/m, and the coefficient of friction is 0.25. The input power of the belt is 60 kW at 1000 rpm. Calculate the following when the center distance is 3.5 m. (a) Maximum tensile stress of the belt(b) Axial load on each pulley
8. A cross belt arrangement has centre distance between pulleys as 1.5 m. The diameter of bigger and smaller pulleys are 'D' and 'd' respectively. The smaller pulley rotates at 1000 r.p.m. and the bigger pulley at 500 r.p.m. The flat belt is 6 mm thick and transmits 7.5 kW power at belt speed of 13 m/s approximately. The coefficient of belt friction is 0.3 and the density of belt material is 950 kg/m³. If the permissible tensile stress for the belt material is 1.75 MPa, calculate: 1. Diameters of pulleys; 2. Length and width of belt. [Ans. 500 mm, 250 mm ; 4.272 m, 90 mm]
A steel tire, 20 mm thick, 90 mm wide, and 1600.0 mm inside diameter is heated and shrunk onto a steel wheel 1600.5 mm in diameter. If the coefficient of static friction is 0.40, what torque is required to twist the tire relative to the wheel? Neglect the deformation of the wheel. Use E = 100 GPa.
The figure shows a system with a block m1 attached to a simple square thread screw with a mean diameter of 10 mm, a pitch of 3 mm and whose coefficient of static friction on the thread is 0.35. Block m1 is attached to block m2 by a rope, each of blocks m1 and m2 have a mass of 4 kg.Block m2 is in turn attached to a 15-kg block W by another rope, which passes over a static drum where the coefficient of static friction is 0.20. Determine the required Moment M that must be applied to the screw to start lifting block W. The coefficient of static friction between the surface and blocks m1 and m2 is 0.25. Need free body diagrams
I will rate helpful. Thank you.
A block brake with a torque of 250 N-m. Its drum rotates at 100 rpm. The length of the block (1) is twice its width (w). Assume, the coefficient of friction P is 0.35. Calculate: (1) the applied load (P) and the hinge-pin reaction (Rx ana Ry) for clockwise rotation of the drum; (2) the applied load and hinge-pin reaction for anticlockwise rotation of the drum; (3) the rate of heat generated during the braking action. (4) The dimensions of the block, if the intensity of pressure between the block and brake drum is 1 MPa. (5) Check whether the brake is self-locking.
Two pulleys, one 650 mm diameter and the other 400 mm diameter, on parallel shafts 1.5 m apart are connected by a flat belt. Find the length of the belt required and the angle of contact between the belt and each pulley. What power can be transmitted by the belt when the larger pulley rotates at 1200 rev/min, if the maximum permissible tension in the belt is 10 kN, and the coefficient of friction between the belt and pulley is 0.05? dont write handwritten solution.