A 78-percent efficient 12-hp pump is pumping water from a lake to a nearby pool at a rate of 1.2 ft3/s through a constant-diameter pipe. The free surface of the pool is 32 ft above that of the lake. Determine the irreversible head loss of the piping system, in ft, and the mechanical power used to overcome it.

Q: An oll pump is drawing 18 kW of electric power while pumping oil with density 860 kg/m³ at a rate of…

A: Here, given data power(We)=18kWdensity(ρ)=860kg/m3flow rate(Q)=0.1…

Q: A mechanical device pumps the fluid from a depth of 150 m under steady conditions. The density of…

A: Given data  depth=150m  density of fluid=1020 kg/m2  efficiency =70%  velocity of fluid =150m/s…

Q: Electric power is to be generated by installing a hydraulic turbine-generator at a site 70 m below…

A: Given   Shaft power, Pshaft = 800 kW         Electrical power, Pelec = 750 kW…

Q: Water is pumped from a lake to a storage tank 15 m above at a rate of 70 L/s while consuming 15.4 kW…

A: The electric power supplied to the pump is The power supplied to the water by the pump can be…

Q: The pump of a water distribution system is powered by a 15-kW electric motor whose efficiency is 90…

A: Given that → Power inputW.=15 kW                    nmotor=0.9                    V.=50LS=50x10-3…

Q: Water enters a hydraulic turbine through a 30-cm-diameter pipe at a rate of 0.7 m3/s and exits…

A: The given data is shown in the following attached image:

Q: A pumped storage scheme comprises two reversible pump turbines which transfer water between an upper…

A: Disclaimer:Hello. Since you have submitted multiple questions, we will solve the first one for you.…

Q: A water pump delivers 6 hp of shaft power when operating. If the pressure differential between the…

A: The given information in the problem is listed down in the following attached image:

Q: when operating. If the pressure differential between the outlet and the inlet of the pump is…

A: Given:  Power developed by the pump, P=6 hp Pressure difference, p=1.2 psi Flow rate, Q=15 ft^3/s

Q: A 78-percent efficient 12-hp pump is pumping water from a lake to a nearby pool at a rate of 1.7…

A: The useful pumping power  is expressed as follows-Pumping head-

Q: Consider water flow in a piping network. The pressure, velocity, and elevation at a specified point…

A: Write the Bernoulli's equation between points 1 and 2. Here, P1 is the pressure at point 1, v1 is…

Q: Water is being pumped from a large lake to a reservoir 25 m above at a rate of 25 L/s by a 17-KW…

A: According to the given data V˙=25L/s=25x10-3m3/s Wshaft=17 kW z2-z1=25m hL=5m We need to find…

Q: Water enters a hydraulic turbine through a 35-cm-diameter pipe at a rate of 0.8 m3/s and exits…

A: Bernoulli's equation relates the pressure energy, kinetic energy and potential energy of a fluid…

Q: A dam with a hydraulic turbine–generator located 40 m below the water surface has a rate of 4600…

A: Given that: Elevation = 40 m Mass flow rate = 4600 kg/s Electric power output = 1400 kW Generator…

Q: (a) A storage tank is connected to a piping system as illustrated in Figure P1. Water at temperature…

A: Major and minor losses are the most common types of energy losses in fluid flow across a pipe…

Q: Water with density 1000 kg/m3 and gauge pressure 31.5 kPa flows through a ground level pipe with…

A: The density of water,(ρw)=1000 kg/m3 The gauge pressure of the water,(P)=31.5 kPa The velocity of…

Q: Consider a river flowing toward a lake at an average speed of 3 m/s at a rate of 500 m3/s at a…

A: Given: The average speed of the river is v=3 m/s. The rate of the flow of the river is V=500 m3/s.…

Q: The blades of a wind turbine turn a large shaft at a relatively slow speed. The rotational speed is…

A:

Q: The blades of a wind turbine turn a large shaft a relatively slow speed. The rotational speed s…

A:

Q: n oil pump is drawing 35 kW of electric power while pumpi

A: Given: The power of motor is, Pmotor=35 kW. Density of oil is, ρ=860 kg/m3. The flow rate is, Q=0.1…

Q: In a pumping system handling water, the surface level of water in the open suction tank is 3m below…

A: The suction level below the pump center is hs=3 m. The delivery level above the pump center is hd=21…

Q: Electric power is to be generated by installing a hydraulic turbine-generator at a site 120 m below…

A: Hydraulic Head  of Turbine, H=120mWater flow rate, m˙=930 kg/sMechanical power output,PM=850…

Q: An 80-percent-efficient pump with a power input of 20 hp is pumping water from a lake to a nearby…

A:

Q: Water is flowing through a venturi meter whose diameter is 7 cm at the entrance part and 4 cm at the…

A:

Q: In a certain application, a siphon must go over a high wall. Can water or oil with a specific…

A: If the pressure at the topmost point falls below the vapor pressure the corresponding fluid then…

Q: Water is pumped from a lake to a storage tank 15 m above at a rate of 70 L/s while consuming 15.4 kW…

A:

Q: Determine the discharge of a flowing fluid from a nozzle, whose specific gravity is 1.3, the nozzle…

A:

Q: A pressurized tank of water has a 10-cm-diameter orifice at the bottom, where water discharges to…

A: In order to proceed with the given problem, the following assumptions need to be taken into…

Q: 1.  Water horsepower of the pump 2.  Brake horsepower of the pump 3.  Power input to drive the…

A:

Q: Water is to be pump from a reservoir with a temperature of 32°C at sea level. Friction loss at…

A:

Q: An 80-percent-efficient pump with a power input of 30 hp is pumping water from a lake to a nearby…

A:

Q: The pump of a water distribution system is powered by a 15-kW electric motor whose efficiency is 95…

A:

Q: In a hydroelectric power plant, water at 20℃ is supplied to the turbine at 1.2 m3/s through a 200 m…

A:

Q: The blades of a wind turbine turn a large shaft at a relatively slow speed. The rotational speed is…

A:

Q: fluid is flowing in a 1.629 m x 0.47 m channel at the rate of 5.45 m/s and has a specific volume of…

A: Given:A=1.629*0.47 m2V=5.45 m/sv=3.668 m3/Kg

Q: A water jet that leaves a nozzle at 53.24 m/s at a flow rate of 117.37 kg/s is to be used to…

A: Nozzle is a device which converts pressure energy into kinetic energy. At the exit of nozzle, only…

Q: Water flows steadily at a rate of 80 kg/min through a pump. The water pressure is increased from 100…

A: Given data,  m= 80 kg/min = 1.333 kg/s  P1=100 KPa  P2= 5150 KPa  v= 0.0015 m³/kg

Q: Electric power is to be generated by installing a hydraulic turbine-generator at a site 70 m below…

A:

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.