A 750-mm-long spring is compressed and confined by the plate P, which can slide freely along the vertical 600-mm-long rods. The 40-kg block is given a speed of v=5m/s when it is h=2 m above the plate. Determine how far the plate moves downwards when the block momentarily stops after striking it. Neglect the mass of the plate.

Q: The turbine develops 150 kW of power, which transmitted to the gears such that C receives 70% and D…

A: P = 150 kWd = 100 mmG = 75 GPa or 75000 MPa = 800 rpm

Q: The 5-kg collar has a velocity of 5 m/s to the right when it is at A (Figure 3). It then travels…

A: Answer We are given  Mass of collar mc = 5 kg Velocity at point A is VA= 5 m/s Unstretched length…

Q: Calculate the reactions of the beam using Moment Distribution Method P = 29 k, W = 2.4 k/ft, a =…

A: Concept We will use method of moment distribution to get the final moment at supports then by…

Q: The A-36 solid steel shaft is 2 m long and has a diameter of 67mm. It is required to transmit 69kW…

A: The given data is shown below: A-36 steelLength=2mDiameter=67mmPower=69 kWAllowable shear stress=80…

Q: The 7.0-lb bar is pinned at its center O and connected to a torsional spring. The spring has a…

A:

Q: find the reaction of the wall at A on the lower shaft

A: balancing the two spheres first draw free body diagram of both sphere seperatly

Q: Determine the horizontal component of reaction at C. 500 lb/ft 300 lb/ft 300 B fixed A pin C roller…

A: Consider the figure,

Q: A closed cylindrical tank 30 cm in diameter and 120 cm high contains 90 cm of liquid SL = 0.80). The…

A:

Q: From the frame loaded as shown, determine the reactions Ra, RD, and moments MA and Mc. 20 kN 40 kN…

A:

Q: The jib crane is designed for a maximum capacity of 4 kN, and its uniform I-beam has a mass of 210…

A: NOTE : Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: The total mass of the system is given as 20 kg with mass center at point D. The assembly is mounted…

A: Equilibrium Equations: Equilibrium equations are required to solve any unknown forces acting on the…

Q: 3. The pendulum consists of a 5-lb solid ball and a 2-lb uniform rod. If it is released from rest…

A: Given ::

Q: A 3-ft-diameter pipe is supported every 16 ft by a small frame like that shown. Knowing that the…

A: To find:- a) Components of Reaction at E b) Components of force exerted at C on member CDE Given:-…

Q: Q The two-steel shaft shown in figure have the same diameter and weight 120 lb each. Neglect the…

A:

Q: AL SUrtace With an unkhown thictional coefficient egligible frictional coefficient. The panel has…

A:

Q: In the Figure shown, calculate the mass of the cylinder is 200 kg and that of member AB is 50 kg.…

A:

Q: The 14.6 lb lever OA with 9.6 in radius of gyration about O is initially at rest in the vertical…

A:

Q: The beam shown in figure carries a triangular load which varies from 20 kN/m at A to 0 kN/m at B and…

A: Given:Required:Reaction at BLocation of zero shear from AMaximum momentMoment at point B

Q: The 5.5 kg lever OA with 250 mm radius of gyration about O is initially at rest in the vertical…

A: Given :

Q: There is a (45/10) kg slider ring is going down from the rest position A and slides in frictionless…

A: Given data Mass, m =4510=4.5 kgh=10 mSpring constant, k= 24 kN/m a} Apply the energy conservation at…

Q: The 5kg collar has a velocity of 9 m/s to the right when it is at A. It then travels down along the…

A:

Q: 4. The engine hoist is used to support the 160-kg engine. Determine the force acting in the…

A: To Determine The force acting in the hydraulic cylinder AB, the horizontal and vertical components…

Q: 2m 50 mm B - k = 1500 N/m E *15-72. A 10-kg block A is released from rest 2 m above the 5-kg plate…

A:

Q: -3 ft- 100 lb 3 ft- B 200 lb-f 2 ft 13 12. B 15 Determine the reactions on the bent rod which is…

A:

Q: Determine the reactions on the bent rod which is supported by a smooth surface at B and by a collar…

A: Given :

Q: 4. The engine hoist is used to support the 160-kg engine. Determine the force acting in the…

A:

Q: A simply supported beam with a length of 5 m is carrying a uniform load of 10 KN/m throughout the…

A: In the given question a simply supported beam is given which carries a concentrated load of 10 KN at…

Q: 5. For a fluid at rest, the shear stress is zero. 6. Newton's law of viscosity for a fluid states…

A: As per guidelines we need to answer only 1st question so repost rest question separately

Q: Determine the reactions at the pin A and the roller E. If (P= 3000 N ). %3D

A:

Q: reactions at K and L. (I Vour a ncwe must be

A: GIVEN A STRUCTURE AND WE HAVE TO CALCULATE THE REACTIONS AT K AND L

Q: The motor delivers 3000 hp to the shaft at 1500 rev/min, and efficiently transmitted to gear B and…

A: Given, P = 3000 hp  f = 1500 rpm  G = 77 GPa

Q: Determine the magnitude of the reaction moment at the point O, if the magnitude of the distance X…

A:

Q: . The tapered circular steel shaft is attached to a hollow circular steel shaft. Compute the angle…

A:

Q: The spring has a stiffness k and an unstretched length lo. As shown, it is confined by the plate and…

A: To find:Determine the speed at A

Q: W = 300 N 1.15 m W =1250 N -1.85 m 4.5 m-

A: For the given cylinders, the reaction at D is 519.62

Q: Consider the pipe assembly in (Figure 1). {30i+20j 30k} N and (60i 10j-35k} N. F1 F2 0.8 m 1.20 m…

A: Step 1: Step 2: Step 3:Solution is given aboveStep 4:

Q: Considering the beam provided below, fixed support at point A, an internal hinge at points B and C,…

A: