Answered: A 600mm diameter pipe, 720m long…

A 600mm diameter pipe, 720m long carries water at the rate of 2.5m/s. What is the water hammer pressure if the valve is closed in 1.2 seconds? Use Ewater = 2.2x109Pa and pw = 1000kg/m3.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A liquid having specific gravity of 2.0 is flowing in a 50mm diameter piper. The total head at a…

A: A liquid which having some specific gravity is given in the question which is flowing through a pipe…

Q: Water flows from reservoir A to B through the three concrete pipes shown below. Assume that concrete…

A: GivenH=20mL1=2500md1=400mm or D1=0.4mL2=1850m, d2=300mm or D2=0.3mL3=800m, d3=200mm or…

Q: A

Q: (c) Figure Q4(c)(i) shows the system consists of 1200 m of 5 cm cast-iron pipe, two 45° and four 90°…

A: L = 1200 mD = 5 cm or 0.05 m Q = 0.005 m3/s = 0.001 kg/m s

Q: A horizontal Venturi flow meter consists of a converging-diverging conduit as indicated in the…

A: The volume flow rate Q of a fluid is defined as the flow rate of fluid through a given…

Q: Q.2.8 MASS FLOW AT A PIPE JUNCTION Consider the s. tv low in a water pipc joint shown in the…

Q: A pipe (AB) that is 2300 m long and 400 mm diameter ,carries 150 L/s, C%=D100 ,the elevation of…

Q: Estimate the maximum water hammer pressure generated in a rigid pipe of a 3 m dia pipe with an…

A: Given- Diameter of the pipe- d=3 m,L=8000 m,t=4 s,V=3 m/s, It is needed to find the critical time of…

Q: discharge pipe in which the velocity is 2.40m/sec. At point A in the suction p pressure is - 40kPa.…

A: Given:- diameter =200mm discharge pipe dimater =150mm To find:- Power

Q: Example 3: A pipe gradually tapers from 0.6m at A to 0.9m at point B. the elevation difference…

Q: A valve is suddenly closed in a 200 mmø pipe. The increase in pressure is 700 kPa. Assuming that the…

A: compute the water hammer pressure in kPa at the valve if it is closed in 3 sec.

Q: PROBLEM O3: Given the figure below, (a) determine the flow rate in the siphon shown. Diameter of the…

Q: Calculate the discharge through the orifice.

Q: ill be the flowrate? The pipes are galvanized iron with k, = 0.0005 ft. Take v = 1.06 x 5 ft/s and…

A: To find:Flow rate

Q: 1. Kerosene (p = 804 kg/m³ ; µ = 1.92x10-3 kg/m-s) is pumped at 0.15 m³/s through 20 km of…

A: Calculate the head loss and the pressure drop through the pipe.

Q: A straight pipe AB, of length 10 m, tapers from a diameter of 40 cm at A to 20 cm at B. The centre…

Q: Water flows from the tank shown in the figure below. At a depth of 1.5 ft the rate of change of…

A: Total length of pipe= 18ftDiameter of pipe = 0.4 inFriction factor = 0.03Loss coefficient For…

Q: The volumetric flow through the pump in the figure is Q = 0.014 m3 / s. The fluid being pumped is…

Q: Oil (SG = 0.83) flows at a rate of 200 L/s through a 500m pipe with a diameter of 200mm. The…

Q: 4FT A h water

Q: The figure shows a portion of a hydraulic circuit. The pressure at point B must be 250psig. When the…

A: Given data: Pressure at point B, PB=200 psig Volume flow rate, Q=80galmin Specific gravity…

Q: Nozzle

A: To calculate pressure head at point 2. Applying Bernoullis equation at point 2 and exit. Note that…

Q: The flow rate for the pipe system is 0.050 m³/s with a total head loss of 12 m. Use C = 120 for all…

Q: 2000 m 45 cm ở Q= 400 litres/s 600 m 30 cm 6 FIGURE D

A: Given that....

Q: Given Water at 10°C flows at the rate of 970 L/min from the reservoir and through the pipe shown in…

Q: A steel pipe has an inside diameter of 25mm, is 20 meter long, carries 10degree water at the rate of…

A: what is the static pressure of the water at the outlet,P2=?

Q: A 25 cm circular pipe carries 2536.06 gpm of water under a pressure of 200 pa. The pipe is laid at…

Q: Q2/ Three pipes are connected in series. The physical properties of the pipes are in Table below. If…

A: PA - PB = 150 kPa ZA - ZB = 5 m v = 1.02 x 10-6 m2/s

Q: The diameter of a pipe gradually reduces from 1 m to 0.7 m. the pressure intensity at the centre…

Q: Subject hydraulics: Consider FIGURE R1M—3. Determine the discharge and the pressure head at A and B…

Q: 1. A pipe of diameter 1.1 ft narrows to a diameter of 0.8 ft. Air moves through the pipe at a mass…

A: given mass flow rate, m. = 6.1 Pressure and temperature at section 1 P1 = 110 + 14.7 = 124.7 psia…

Q: storage tank located 30m above the pump. The suction pipe is 350mm in diameter and 12m in length,…

Q: Given below are pipe lengths, sizes and connections. All pipes have a friction factor of 0.020. If…

A: Given Data:Friction Factor=0.020V=8cfsPipe 1length=2750ftdia=21inPipe 5length=4750ftdia=27in

Q: The water is flowing with a velocity of 1.5 m/s in a pipe of length 2500 m and of diameter 500 mm.…

A: Using formula

Q: A straight pipe AB, of length 10 m, tapers from a diameter of 40 cm at A to 20 cm at B. The centre…

Q: A venturi meter with a 10.16 cm throat installed in a 15.24 cm pipe which is inclined upward with an…

Q: A horizontal 250-mm pipe suddenly enlarges to a 300-mm diameter. If the flow is 0.15 m³/s of water,…

A: Given data in question Diameter 250 and 300 mm Horizontal pipe Pressure at smaller Diameter 265 kPa…

Question

A 600mm diameter pipe, 720m long carries water at the rate of 2.5m/s. What is the water hammer pressure if the valve is closed in 1.2 seconds? Use Ewater = 2.2x109Pa and pw = 1000kg/m3.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

L = 900m D=35cm L=600m L=900m D=75cm D=60cm L=600m D=30cm L=900m D=40cm A flow rate of 0.5 m³/s is branched into three pipes and then rejoined in the concrete parallel pipes as shown in the figure below. Find the head of loss between point A and point B. Here, the coefficient of friction loss in all tubes is 0.03.
Q6. Absolute vapor pressure of water siphoned is 2.25 kPa. Water is extracted from a reservoir as shown in figure below. Diameter of the pipe is D= 16 cm. (Patm=100 kPa, Ywater-9810 N). Please answer the following questions. (1) Zmax a) Determine the flow rate of the system. b) Determine the maximum elevation of the highest point of the piping system without causing cavitation (Zmax=?).
A 56-mm-diameter siphon is drawing oil (SG = 0.818) from an oil reservoir, as shown in the figure. If the velocity of flow in the pipe is 'v, the head loss from point 1 to point 2 is 2v2/2g, and the head loss from point 2 to point 3 is 5v2/2g. Find the absolute pressure (in kPa) at point 2. Use atmospheric pressure, Patm = 101.38 kPa. Use y1 = 2 m., and y2 = 5 m %3D
Water flow at a 250mm diameter horizontal pipe 875m long. The friction factor is 0.023. If the pressure at the starting point is 80KPA and the pressure at the end point is 50KPA. Determine the discharge at the pipe. A Q = 153.68 L/s В No answer among the choices C) Q = 101.07 L/s D) Q = 118.43 L/s E Q = 132.74 L/s F Q = 172.81 L/s %3D
A cylindrical tank of water is 20 m in diameter and 3.5 m tall. There is a 1.0 cm diameter hole at the bottom from which water is leaking. A feeder pipe at the top of the tank, 4.0 m above the ground delivers water at a rate of 0.02 m/min. Ir the tank is initially half full, tal what is the water flow rate in m^3/sec from the top feeder pipe? (bi what is the pressure at the bottom of the tank? (Hint: Bernoul's principle) () what is the water speed at the bottom? (d) what is the leaking flow rate at the bottom? fe) at what rate is the volume of water changing? (Assume the tank is open to air at the top)
Determine the friction loss if the friction factor is 0.4 and velocity of the flow is 40 m per sec. Given length of the pipe is 20m, inner diameter 0.3m. Use friction loss formula. Using the calculated friction loss, solve for the ffg: a. What is the pressure drop due to the Bernoulli effect as the water goes into a 3.00-cm-diameter nozzle froma 9.00-cm-diameter fire hose while carrying a flow of 40.0 L/s? b. To what maximum height above the nozzle can this water rise? (To actual height will be significantly smaller due to air resistance.)
Along a 50-m pipeline, there is a half-open globe valve (K = 10), four 90-degree smooth bends (K = 0.45), and six 45-degree elbows (K = 0.15). Ignoring the major head loss, what will be the pressure drop in this pipe if the flow velocity is 1 m/s? Fluid is water: Specific weight = 9810 N/m³. O 0 kPa O 6.35 kPa O 13.81 kPa O 21.67 kPa