A 600 kg material is hung from the end of the horizontal bar BD as shown. Determine the stress on the rod AC if its diameter is 25 mm. Use 2 decimal places in every solved values A 1.5 m B D 2 т 1 т

Q: A rectangular block is 103 mm long in the X direction, 99 mm wide in the Y direction, and 58 mm…

A:

Q: A beam subjected to a bending moment of 37.7 Nm and having the following sectional properties:…

A:

Q: me design strength (Mu) of the T-beam sh

A: f'(c) =27 MPa, fy = 350 MPaNeed to findDesign strength of beam

Q: Figure a 1 of 1 > Determine the moment of inertia of the composite area about the x axis. Set a =…

A: Given data in question  Sectional area Dimensions = 130 mm Squares  and  triangle To find out…

Q: Show FBD and complete solution.    The system of knotted cords shown in the figure support the…

A: To find tensile force in each rod

Q: - the upper part in fig below is a steel and lower part is a cast iron , the load P shortens the…

A:

Q: During the design of a building the deflection of a beam is calculated to be 0.90 inch. In order to…

A: i = 0.9 in a = 0.75 in

Q: Water flows through a 0.05 m diameter of cast iron as shown below. What percent of the total head…

A: Given Data: Diameter=0.05mk=0.9v=8m/sh=2m To determine:- percentage of total head loss caused by…

Q: Problem Number 1: In the given composite structural section determine the quantities placed in the…

A:

Q: Determine the diameter (in mm) of the largest circular hole that can be punched into a sheet of…

A: Given data, Thickness of the polystyrene sheet, = 6.75 mm Force exerted by the punch, = 42.9 kN…

Q: The shear force acting at the section is V = 38 kip. S in 6 in

A:

Q: The tensile test of a specimen of rebar conducted by students in the Construction Materials and…

A: Given data:  The tensile test of a specimen of rebar conducted by students in the Construction…

Q: Stress analysis Task Question / Calculate the critical design loads applied to the Stirling Engine…

A: Please find the answer in the below attachments

Q: alculations You must plot the data correctly,(the material weight = gm ) Sieve Mass Retained Percent…

A: in this question curve between  percentage passing and sieve size is being asked . and we have to…

Q: If an A36 steel rod under tension load has a strain gage that measures 0.003 in/in, what is the…

A: Given:- The steel rod under tension load = A36 The strain measured by strain gage = 0.003 in/in To…

Q: Condition #1: A structural support for a machine is subjected to a static compression load of 20 kN.…

A:

Q: Q1: Why Iraqi specification no. 5 limited max. SO3 by 2.5% when C3A !7%. *

A: Brief concept introduction- Iraqi Specifications No. (5), 1984 for Portland Cement.- Iraqi…

Q: Determine the moment of inertia of the composite area about the axis. Set a = 660 mm, b = 220 mm, h…

A:

Q: 30 mm 15 mm 70 mm 30 mm 55 mm B" /B 110 mm 100 mm DA 70 mm 30 mml The block is deformed into the…

A:

Q: Add FBD & explain work

A: Step 1:Problem StatementYou are provided with the following data for a steel beam:( E = 29,000 )…

Q: What pressure (MPa) is required to reduce the volume by 0.66% ? Bulk modulus of elasticity of wa EB=…

A: The given data in the question is the bulk modulus of elasticity of water, EB=2.11 GPa, and the…

Q: Determine the moment of inertia of the composite area about the y axis. Set a = 160 mm, b = 160 mm,…

A: a = 160 mm b = 160 mm h = 80 mm r = 50 mm To find:- Moment of inertia about y-axis

Q: ensile strength of 67.819 psi. The original gage length was 2 inches

A: Given:- tensile strength=67.819psi originalgauge length =2 inches gauge length2.75 inches To find:-…

Q: The composite plate is made from both steel (A) and brass (B) segments. Take pst = 7.85 Mg/m³ and…

A:

Q: A bridge/joint table is exactly what its name implies. What is the substitute? What is wrong with…

A: A bridge table is a table that just holds back the keys between the two tables in a many-to-numerous…

Q: What standard diameter deformed bar used as stirrups for beam? 10 mm diameter O 8 mm diameter O 6 mm…

A: Stirrups are rectangular loops built from a plain round bar that contain or restrain the primary…

Q: (i) Determine the angle of threaded screw, 0. (ii) Find the angle on static friction, Øs. (iii)…

A: Given Data: The pull effort is given as P=25.9 N. The mass of a block is m=100 kg. The diameter of…

Q: A tensile test is peformed on a brass specimen 10 mm in diameter using a gage length of 50 mm. When…

A:

Q: Determine the importance and role of Unit Weight in the construction material utilization.

A: To determine the importance of unit weight of soil in construction material.

Q: Problem Number 1:In the given composite structural section determine the quantities placed in the…

A:

Q: 10. A wood stave pipe, 120 cm in inside diameter, is to resist a maximum water pressure of 1,200…

A:

Dimensional homogeneity

The term dimensional homogeneity means that in an equation, the dimensions of each term on both sides are equal, which means the dimensions of the left-hand side (LHS) of an equation are similar to the dimensions of the right-hand side (RHS). For a dimensionally homogeneous equation, the powers of fundamental dimensions will be identical on both sides of the equation.