A 6 m length beam with rectangular cross-section of WxH: 100x200 mm². The beam is subjected to the loads shown in Figure 1. Determine the maximum deflection between A and B using one of the methods that have been covered in the class. E= 200 GPa. 6 kN/m 20 kN 200 mm -1.5 m- 3 m -1.5 m- 100 mm Figure I

A 6 m length beam with rectangular cross-section of WxH: 100x200 mm². The beam is subjected to the loads shown in Figure 1. Determine the maximum deflection between A and B using one of the methods that have been covered in the class. E= 200 GPa. 6 kN/m 20 kN 200 mm -1.5 m- 3 m -1.5 m- 100 mm Figure I

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A simply supported beam, 6m in length, has an initial deflection of 0.50mm at midspan due to its own weight. The said beam is then use to carry the loads as shown. If E=24,870MPa and 1=5400x106mm, determine the following: (Use Area-Moment Method) 1. Weight of the beam in kN/m 2. Maximum Deflection 8kN 5kN 10KN/m 6m
4) A cantilever beam supports a uniformly varying load and a couple as shown in the figure. If EI = 300.65 kN m², determine the value of maximum deflection in millimeters. 4m B 180 N-m 2m 10 N/m
helppp
Question 3 Determine the value of a in meters so that the deflection at point C is equal to the max deflection between A and B. Use E = 200 GPa and I = 5 x 10' mm4. P = 2.3 kN A a 10 m
please mention every step thanks
3. A steel beam is loaded as shown in the figure. Use conjugate beam method and determine the following: а. Slope at A b. Slope at B c. Displacement at the point of application of the 15kN load d. Displacement at C e. Location and maginitude of maximum deflection 15 kN 1.10 kN/m A 2 m 2 m 2 m
A cantilever beam, 3.5 m long, carries a concentrated load, P. at mid-length. Given: P = 200 KN Beam Modulus of Elasticity, E = 200 GPa Beam Moment of Inertia, I = 60.8 x 10 mm 1.75m ť How much is the deflection (mm) at mid-length? Select the correct response 100 1.84 29.4 23.5 1.75m
I need solution of both the parts
For the beam loaded as shown in the figure below, determine the following unknown using any geometric method. Consider 250 mm x 400 mm (b x h) section and E = 120 GPa. a. Deflection at C in mm. Enter absolute value only. a = 4.5m, b= 24kn/m, c = 3 5kn c kN b kN/m "a m FIGURE 5 For the beam loaded as shown in figure 5, determine the following unknown using any geometric method. Consider 250 mm x 400 mm (b x h) section and E-120 GPa. b. Slope at B in degrees, Enter absolute value only.
For the beam shown, solve for the deflection (in mm.) at B. Use the following data: W = 2.3 kN/m L= 5 meters E = 357 GPa |= 305 x 10^6 mm^4 ROUND OFF TO THREE DECIMAL PLACES. INPUT THE VALUE ONLY W kN/m A В L m.