A 55 hp, 440 V, 400 rpm DC shunt motor draws 107 A when operating at rated conditions. The motor has an armature-circuit resistance of 100 mW and a total field-circuit resistance of 55 W. Answer the following and explain why you chose that answer. (i) What is the motor armature current? 99 A 102 A 107 A 110 A 115 A

A 55 hp, 440 V, 400 rpm DC shunt motor draws 107 A when operating at rated conditions. The motor has an armature-circuit resistance of 100 mW and a total field-circuit resistance of 55 W. Answer the following and explain why you chose that answer. (i) What is the motor armature current? 99 A 102 A 107 A 110 A 115 A

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter5: Resistors

Section: Chapter Questions

Problem 1PA

See similar textbooks

Similar questions

459. The current drawn by a 460 V dc motor of armature resistance 0.5 ohm and back emf 420 V is -
a 220-v dc motor is running at a full load speed of 800 rpm and draws 100 A. calculate at what speed the motor will run when developing half torque. the total resistance of the armature and field is 0.1 ohm
A series motor runs at 700 rev/min when the voltage is 300 V and the current is 20 A. The armature resistance is 0.3 2 and the series field resistance is 0.1 2. Determine the resistance to be connected in series to reduce the speed to 500 rev/min with the same current
Answer please in 10 minutes
A 55 hp, 440 V, 400 rpm DC shunt motor draws 107 A when operating at rated conditions. The motor has an armature-circuit resistance of 100 mQ and a total field-circuit resistance of 55 0. Draw a schematic of the motor in the space below showing all known quantities (resistances, currents, voltages and load). Show only symbols for unknowns.
3.62 A squirrel cage induction motor having a rated slip of 2% on full load has a starting torque of 50% of full load torque. The starting current is (a) Two times the full load current (b) Four times the full load current (c) Five times the full load current (d) Equal to the full load current
Reducing the supply voltage so that Vnew = Vold / V3 reduces the maximum torque of the motor so that Tmaxnew= ...Tmaxold . * .... ...
L-1). The 3-phase wound-rotor induction motor has .... . a) high starting torque b) low starting current c) both "a" and "b" d) neither "a" nor "b" L-2). The 3-phase wound-rotor induction.........a) motor has a wire wound rotor b) motor's rotor can be connected to an external resistive load by way of slip rings and brushes c) motor requires more maintenance than the 3-phase squirrel-cage induction motor d) all of the above L-3). The 3-phase wound-rotor induction motor's rotor circuit's resistance should be adjusted so it is__________ during starting. a) low b) high c) either "a" or "b" d) neither "a" nor "b" L-4). Will a 3-phase wound-rotor induction motor start with no external circuit connected to its rotor leads? a) yes b) no
i need the answer quickly
A 220 V shunt motor driving its normal load draws an armature current of 50 A from a 220 V dc source. The armature resistance of this motor including brushes is 0.25 ohms. How much armature current (minimum) Will this motor draw from a 200 V DC source when driving the same load with the field adjusted to maintain the same speed.
A 220V. dc series motor is running at a speed of 800 rpm and draws 100 A. Calculate at what speed the motor will run when developing half the torque. Total resistance of the armature and field is 0.10.
The current drawn by 220 V dc shunt motor of armature resistance 0.5 ohm and back emf 200 V is