A 540-N uniform rectangular sign 4.00 m wide and 3.00 m high is suspended from a horizontal, 6.00-m-long, uniform, 140-N rod as indicated in the figure below. The left end of the rod is supported by a hinge and the right end is supported by a thin cable making a 30.0° angle with the vertical. (Assume the cable is connected to the very end of the 6.00-m-long rod, and that there are 2.00 m separating the wall from the sign.) (a) Find the (magnitude of the) tension T in the cable. N (b) Find the horizontal and vertical components of the force exerted on the left end of the rod by the hinge. (Take up and to the right to be the positive directions. Indicate the direction with the sign of your answer.) horizontal component _____N vertical component _____N

Q: A flanged wooden shape is used to support the loads shown on the beam. The dimensions of the shape…

A: To find:maximum tension bending stressmaximum compression bending stress

Q: Consider a rigid rod that is subjected to two external forces and is fixed to the wall at A. The…

A:

Q: The cover in the figure is in the form of a quarter circle, its width perpendicular to the paper…

A: Given Data: width of the gate w=3 m Weight of the gate Wg=15 kN Find: the minimum value of the…

Q: Figure 2.4 shows a rope is supporting a 185 kg uniform beam which is 16.0 m long. One end of the…

A:

Q: QUESTION 4) For the given system shown in the figure, the AB bar is in the 4m direction of z-axis…

A: Given: The diameter of OB and AB, D = 100 mm = 0.1 m The radius of disc, r = 0.5 m The allowable…

Q: Horizontal cantilever shart with disks is loaded by 2 concentrated forces. 1 F1 Given: 1=26cm;…

A:

Q: A flanged wooden shape is used to support the loads shown on the beam. The dimensions of the shape…

A:

Q: The metallic hollow pipe shown in Figure Q2 is fixed at its lower end and free at its top end, and…

A:

Q: Question 2) The Russell fracture traction device and a mechanical model of the leg are shown in the…

A: L = 100 cmW = 250 NIt is asked to find the tension T1, T2

Q: A new art exhibit featuring mobile works is going up in the Holland, MI, area. One piece is shown in…

A:

Q: Question 2 You are holding a thin and weightless bar on your head (see figure 2.1). On the extremity…

A:

Q: Hinge supported frame is loaded by two concentrated forces and a couple. F1 a F2 M

A: To determine the reactions.   NOTE: According to Bartleyby's policy we shall answer only one…

Q: The block shown in (Figure 1) has a mass of m = 75 kg, a height H= 1.4 m, and width L = 1.9 m. It is…

A:

Q: Hinge supported beam is loaded by two concentrated forces and a couple. M F, F2 1 Given: /4=20cm;…

A:

Q: In Figure 2, the reaction force in the x- direction at point B is (in kN) اختيارات 15.3- O 15.3 O…

A:

Q: A simple point A as shown in Figure 2. The reaction force at point C is (in kN) Figure 2: 5 m 5 m A…

A:

Q: (a) Find the tension in the support cable. KN (b) Find the components of the reaction force exerted…

A:

Q: a) Find the temperature change in the steel and aluminium rods when the lower end of the aluminium…

A:

Q: To use the equations of equilibrium for a three- dimensional object to solve for the support…

A: Draw the free body diagram:

Q: W T As shown in the figure, two sides of a semicircular trough are hinged to each other at the…

A:

Q: we want to build a single-rail overhead crane in the workshop.when the load reaches the extreme…

A: Given: The extreme location of load, x = 1800 mm = 1.8 m The tensile stress in rope, σ = 600 MPa The…

Q: A flanged wooden shape is used to support the loads shown on the beam. The dimensions of the shape…

A:

Q: A flanged wooden shape is used to support the loads shown on the beam. The dimensions of the shape…

A:

Q: The two bearings (B1) and (B2) are used to support a shaft as shown in the figure Using the data…

A:

Q: The mass-less bar (OAB) shown in the figure is supported by a ball and socket support at point O and…

A:

Q: 1. Three cubes of side l0, 2l0, and 3l0, are placed next to another (in contact) with their centers…

A: 1.a) Position of the centre of the mass from the left side is 3.83l0. b) New mass density would be…

Q: The prismatic bar AC is supported by a hinge at C and cable ADB that runs through a frictionless…

A:

Q: A horizontal L=1.2 m long mb=14 kg uniform bar is hinged on the left end and pulled at the right end…

A:

Q: The pipe is pulled by three cables as shown on the figure below. All three cables are subjected to…

A: Given:-  Fa = 7.5 kN Fb = 1.25 kN Fc = 5 kN To Find :- Summation of forces in x and y axis

Q: The tractor shovel shown (Figure 4) carries a 500 kg load that has its center of mass at H. The…

A:

Q: The cantilever truss in the figure is hinged at D and E. Find the force in member BC. 1000 1b 60 60°…

A:

Q: A sign for a pizza restaurant hangs from a 2.60-m long rod extended out from a building. A cable,…

A:

Q: 2. The structure is connected by a pin joint at point A and by a cable of length L at points B and…

A: The free-body diagram of the above structure is given as, Apply force equilibrium in the vertical…

Q: Three identical circular disks A, B, and C arewelded to the ends of three identical solid circular…

A: Given        Load, P1 = 28 lb Diameter, d1 = 0.5 in                 d2 = 3 in Find Maximum shear…

Q: The cantilever truss in the figure is hinged at D and E. Find the force in member BD. 1000 1b 60°…

A: As per given question  We have to determine all forces members including BD

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.