a 50 m steel tape was standardized and was found to be 0.0042 m too long than the standard length at an observed temperature of 58 degrees celcius. the same tape was used to measure a certain distance and was recorded to be 673.92 m. during measurement, the temperature increased to 68 degrees celcius. determine the total correction of the line.

a 50 m steel tape was standardized and was found to be 0.0042 m too long than the standard length at an observed temperature of 58 degrees celcius. the same tape was used to measure a certain distance and was recorded to be 673.92 m. during measurement, the temperature increased to 68 degrees celcius. determine the total correction of the line.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Given data: K=50 MPa Poisson ratio=0.534 Find E
DBOOM can be closely affiliated with lean because both aim to optimize operating efficiency. True False
A.) Temperature correction for the measured line. B.) Corrected length of the line.
for a sample of water ec reading was called 178 X 10^-3 siemens per centimeter calculate the value of tds in ppt
Prob 2. (15pts) A line was found to be (2865.35+y)m long when measured with a 30-m tape under a steady pull of (6.5+y) kg at a mean temperature of 300C. Determine the correct length of the line if the tape used is of standard length at 200c under a pull of 5.5kg. Assume the cross-sectional area of tape to be 0.025cm2, elastic modulus as 2.10 x 106 kg/cm2, and coefficient of thermal expansion to be 0.0000116/ec.
a steel tape of nominal length 200m with a plumb bob of mass 16kg attached to it was used to measure a length down a shaft as 160.852m. the mean temperature during the measurement was 4'C. if the tape was standardized to be 200.0014m under a tension of 115n at 20'C temperature, determine the correct measured length
This subject is Surveying Lecture. Show your solution step by step
Q5. Look at the following SEM image, then explain: 1- What are the particles mean? 2- Is the wear track horizontal or vertical or both? 20kV Particles O X100 100 Delamination surface 15 40 SEI
There is no more data. Urgenttttttttt
A Civil Engineer used a 50m tape in measuring an inclined distance. The measured length on the slope was recorded to be 459.20 m long. The difference in elevation between the initial point and the end point was found to be 1.25 m. The 50 m tape is of standard length at a temperature of 10°C and a pull of 50 N. During measurement the temperature reading was 16°C and the tape was supported at both ends with an applied pull of 60 N. The cross-sectional area of the tape is 6 mm2 and the modulus of elasticity is 200 GPa. The tape has a mass of 0.075 kg/m. Coefficient of thermal expansion is 0.0000116 /°C. Determine the magnitude of the correction per tape length in meters due to temperature. Round off your answers to 4 decimal places. Determine the magnitude of the correction per tape length in meters due to pull. Round off your answers to 4 decimal places. Determine the magnitude of the correction per tape length in meters due to sag. Round off your answers to 4 decimal places. What is…
A steel tape standardized at 25degree celsius and supported throughout under a tension of 73N was found to be 30.004m long. The tape had a cross sectional area of 5mm^2 and a weigh of 45g/m. This tape was used supported at the ends only with a constant tension of 75N to measure a line from A to B in nine segments. The data given in table 1 were recorded. Apply correction for tape, length, temperature, pull,sag and tape not horizontal to determine the correct length of the line Table 1. Recorded data for nine segments measurements Measured Temperature ("C) Difference in Elevation (m) Section (Recorded Distance, m) А-1 30 15 0.384 1-2 30 15 0.293 2-3 30 16 0.183 3-4 30 16 0.247 4-5 30 16 0.372 5-6 30 17 0.628 6-7 30 17 0.774 7-8 30 17 0.817 15.73 8-B 18 0.570
Show full solutions.