A 50-kg iron block at 80°C is dropped into an insulated tank that contains 50 of liquid water at 25°C. Determine the final temperature when the thermal equilibrium is reached, in °C. (Specific. heat of water = 4.18 kJ/kg.°C)

A 50-kg iron block at 80°C is dropped into an insulated tank that contains 50 of liquid water at 25°C. Determine the final temperature when the thermal equilibrium is reached, in °C. (Specific. heat of water = 4.18 kJ/kg.°C)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A piston cylinder arrangement contains 100 liters of saturated water and 900 liters of saturated steam in equilibrium at 1 MPaa (t;ar = 179.91°C, Vf1 = 1.273x10³ m³/kg and ve1 =194.44x103 m?/kg). Heat is added at constant pressure until the temperature becomes 300°C (At point 2, P2 = 1 MPaa and tą = 300°C, v2 = 257.9x10³ m³/kg). Determine: a) The initial temperature b) The total mass c) The quality of vapor at initial condition d) The final volume e) The work done during the process
Carbon Dioxide (M=44) is being stored at 46°C, 80 bar. The critical temperature and pressure are 31°C and 72.8 bar. Calculate the specific volume. (0.004 m³/kg)
Calculate the pressure of vapor at a temperature of 500°C and a density of 24 kg/m3 using (a) the ideal gas equation, (b) the van der Waals equation, (c) the compressibility factor. Note that the pressure is equal to P= 8000 kpa and find the percentage of error between the three laws
Agas filled in a piston-cylinder arrangement as shown in Figure 1 has a volume of 0.09 m at its initial equilibrium state. The gas is slowly heated through the bottom of the cylinder that allowed for the gas to expand at constant- pressure of 2068 kPa to a volume of 1.24 m. The change in internal energy of the gas is 0.21 kl. Ignoring the friction between the piston and the cylinder and assuming the atmospheric pressure any value from 90 to 110 kPa, (a) Calculate the mass of the piston if the area of the piston is 0.055 m? (b) For the gas as a system, evaluate work and heat transfer, each in k (c) For the piston as a system, evaluate work and change in potential energy, each in kJ Piston- Gas Figure 1: piston-cylinder arrangement
5 kg of air undergoes the cyclic process as shown in the figure. Determine the totalwork done in joules
3000 kJ of heat is given to 1 kg of water at 20 C. If steam with a pressure of 750 kPa is obtained as a result of this process, is this steam wet?institution? You should reach the result by typing the table values and operation steps. TIP: You should decide on enthalpy values using Thermodynamic Property Tables.
Solve by hand please
A 0.5-m3 rigid vessel initially contains saturated liquid–saturated vapor mixture of water at 120°C. The water is now heated until it reaches the critical state(point). Solve, 1. Show the process on T-v diagram with respect to saturation lines. 2. Determine the mass of the liquid water at the initial state.
Provide the solution of advance physics question.
As shown in the figure below, a cylinder fitted with a piston is filled with 600 lb of saturated liquid ammonia at 45°F. The piston weighs 1 ton and has a diameter of 2.5 ft. * Your answer is incorrect. V= What is the volume occupied by the ammonia, in ft3? Ignoring friction, determine the force required, in lbf, by mechanical attachments, such as stops, to hold the piston in place. What is the volume occupied by the ammonia, in ft³? i 15376500 Patm = 1 atm Piston ft3 Ammonia Saturated liquid - Weight = 1 ton D=2.5 ft
c) ofR-134a at an initial pressure of 1.2 MPa is filled in a rigid container with a volume of 24.228 m³. The container is then cooled to 40°C. i. Determine the initial temperature and final pressure of the R-134a. Clearly show all calculations. Ikg ii. Show the process on a properly labelled pressure versus specific volume (P-v) diagram with respect to saturation lines.
A real gas exists at 130 C and 1.2 MPa. It is known that the critical temperature and critical pressure of the gas is 374.2 k and 4.059 MPa. It is also know that the ideal gas constant (R) of the gas is 0.12 kPa-m/ S/kg-K. In the question that follows, select the answer that is closest to the true value. Use the compressibility factor (Z) to determine the specific volume in units of m/kg. ,3, Tuesday Dece mber 7 2021 5:52:58 DM CST