A 50-cm diameter pipeline in the Arctic carries hot oil where the outer surface is maintained at 30 °C and is exposed to a surrounding temperature of -17 °C. The convection heat-transfer coefficient on the outside of the pipe is 9 W/m2 °C. Estimate the energy loss from the pipe per meter of length.

A 50-cm diameter pipeline in the Arctic carries hot oil where the outer surface is maintained at 30 °C and is exposed to a surrounding temperature of -17 °C. The convection heat-transfer coefficient on the outside of the pipe is 9 W/m2 °C. Estimate the energy loss from the pipe per meter of length.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Homework of Chapter Five Q1: Consider the flow of oil with p = 894 kg/m³ and u = 2.33 kg/m.s in a 40-cm- diameter pipeline at an average velocity of 0.5 m/s. A 300-m-long section of the pipeline passes through the icy waters of a lake. Determine the pumping power required to overcome the pressure losses and to maintain the flow of oil in the pipe. Answer: 4.39 kW
An oil has 0.62 inch steel tube, through which flows an oil. The properties of oil are as follows; μ = 0.034 lbs/ft-sec, μb = 0.044 lbs/ft-sec, μw = 0.004 lbs/ft-sec, and specific gravity at 60°F is 0.899. The oil neters at a temperature of t1 = 60°F and flows with an average velocity of 4 ft/sec. The inside surface area is 0.1613 ft2 per foot length, and the inside sectional area is 0.3019 in2. The length of one pass of the tube is 10 feet. Considering steam at 215°F surround the tubes. Assume that the inside surface temperature of the pipe is 210°F and a bulk temperature of 72°F. If the specific heat of oil is 0.5 btu/lbs-°F and its conductivity k = 0.08 Btu-ft/hr-F-ft2, what is the temperature at the end of 10 feet pass. Show your complete solution and illustration.
When a long section of a compressed air line passes through the outdoors, it is observed that the moisture in the compressed air freezes in cold weather, disrupting and even completely blocking the air flow in the pipe. To avoid this problem, the outer surface of the pipe is wrapped with electric strip heaters and then insulated. . Consider a compressed air pipe of length L = 6 m, inner ra- dius r₁ = 3.7 cm, outer radius r₂ = 4.0 cm, and thermal con- ductivity k = 14 W/m - °C equipped with a 300-W strip heater. Air is flowing through the pipe at an average temperature of -10°C, and the average convection heat transfer coefficient on the inner surface is h = 30 W/m². °C. Assuming 15 percent of the heat generated in the strip heater is lost through the insula- tion, (a) express the differential equation and the boundary conditions for steady one-dimensional heat conduction through the pipe, (b) obtain a relation for the variation of temperature in the pipe material by solving the…
A fluid with a surface film coefficient of 500 W / ° C flows through a pipe (k = 40 W / m ° C) with a meter length of 90 mm and an outer diameter of 110 mm. The film coefficient between the pipe surface and the air is 30 W / ° C and there is air at 20 ° C outside environment. What is the pipe tube outer surface temperature (° C)?
Hot air at atmospheric pressure and 80°C enters an 8-m-long uninsulated square duct of cross-section 0.2-m×0.2-m that passes through the attic of a house at a rate of 0.15 m3/s (see figure). The duct is observed to be nearly isothermal at 60° C. Determine the convection heat transfer coefficient (in W/m2∙K) inside the duct. For air at 80°C: ρ = 0.9994 kg/m3; cp = 1008 J/kg∙K; k = 0.02953 W/m∙K; ν = 2.097×10-5 m2/s
A pipe with a 1.5 cm in diameter and 10 min length is gaining 800 W/m2 constant heat from its outer surface. Water enters the pipe at 25 °C with velocity of 0.1 m/s. What is the wall temperature at the exit plane of the pipe? Assume that all gaining heat is transferring the water. For water: k = 0.6 W/mK, ν = 0.75x10-6 m2/s, ρ = 1000 kg/m3, cp = 4187 J/kgK, Pr = 6. Please choose one: A. 30.10 °C B. 40.50 °C C. 34.68 °C D. 35.56 °C
A long copper plate (k= 374 W/m °C, a = 11.23×10-5 m 2 /s) 20 cm thick initially has a uniform temperature of 250 °C. Both outer surfaces are suddenly exposed to a fluid stream at 80 °C. The convection heat transfer coefficient between the plate and the fluid is 935 W/m2 °C. (a) Draw a simple sketch to show the change of temperature inside plate with time. (b) Calculate the temperatures at the outer surface (To) and center of the plate (Tc), after 5 minutes. 1.0 0,7 0,5 0.4 0,3 100 0.2 0.1 0.07 0.05 0,04 0,03 0,02 Slo 0,01 0.007 0.005 0.004 0.003 0,002 0,001 1 2 3 4 6 8 10 12 14 16 18 20 22 24 26 28 30 40 50 60 70 80 90 100 110 130 at/L?= Fo 150 200 300 400 500 600 700 Figure 4-10 | Temperature as a function of center temperature in an infinite plate of thickness 2L, from Reference 2. 1.0 x/L = 0.2 0.9 0.8 0.4. 0,7 0.6 0.6 0.5 0.4 0.8 0,3 0.9 0.2 0.1 1.0 0.01 0.02 0.05 0.1 0.2 0.5 1.0 2 3 5 10 20 50 100 k hL - Bi O/0, = (T – T„(To- T.)
For seaworthiness trial of a new ocean-going vessel design, the total convective heat transfer rate of a fully turbulent water flow over a 10-m×2-m side of a flat plate was measured to be 77.2 kW under a specific steady condition in a test setting. The conditions are: velocity of the water is 0.5 m/s along the 10-m side of the surface; water temperature is 18°C; and surface temperature was uniform at 22°C. What is the friction force (skin friction drag) due to the water flow on the surface?
A mercury thermometer placed in oil well is required to measure temperature of compressed air flowing in a pipe. The well is 150 mm long and is made of steel (k = 50 W/m°C) of mm thickness. The temperature recorded by the well is 150°C while pipe wall temperature is 75°C Heat transfer coefficient between the air and well wall is 50W/m²°C. Estimate true temperature of
Fluid is flowing through a 20 mm inside diameter and 25 mm outside diameter brass tube at no leaking with temperature at 65℃ and length of 10 m. Surface conduction of hot fluid is 5.2W/(m^2℃) and thermal conductivity of brass is 12.84W/(m℃). Brass tube is covered by silica of 6 mm thickness with thermal conductivity of 13.84W/(m℃) . Outside of it, is a fluid with 45℃ with surface conductance of 3.2W/(m^2℃). Find the heat transfer from the hot fluid with temperature of 65℃ to fluid with temperature of 45℃.
Find the heat flow rate through the composite wall as shown in Fig dimensional flow and take . Assume one- k = 150 W/m-deg ; k = 30 W/m-deg ; k, = 65 W/m-deg ; k = 50 W/m-deg 0.09 3 cm D 7 cm 400°C 5 cm В ст 10 cm Э ст
A heater plate measures 40 cm x 40 cm in the tank and is kept at a constant temperature of 70 °C. Show with calculations in which case the oil at the temperature of 30 °C in the tank can be heated the most.