A 5-meter long pipe is inclined at an angle of 15° with the horizontal. The smaller section of the pipe has a diameter of 80 mm while the larger section has a diameter of 240 mm. The smaller section of the pipe is at the reference datum which is lower than the larger section. The velocity of water at the smaller section is 1 m/s. Determine the difference of pressures between the two section in N/m². 80mm то 15⁰ 5m [Dar 240mm (2) -Datum line

A 5-meter long pipe is inclined at an angle of 15° with the horizontal. The smaller section of the pipe has a diameter of 80 mm while the larger section has a diameter of 240 mm. The smaller section of the pipe is at the reference datum which is lower than the larger section. The velocity of water at the smaller section is 1 m/s. Determine the difference of pressures between the two section in N/m². 80mm то 15⁰ 5m [Dar 240mm (2) -Datum line

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Include proper explanation this is fluid mech problem
Question 4. The flowrate of the flow is 0,20 m/s in a pipe placed on a horizontal plane. The pipe diameters are as 0.41 m and 0.28 m for Di and D2, respectively. Find the resultant force *(kN) acting to the pipe by the flow. The gauge pressure at (1) is P1 =280 kN/m2. (y= (1) 10KN/m³) Figure 4
A pump is discharging 12 lit/sec ofwater through 100mm diameter smooth steel pipe. When the pump is 720 kPa, the discharge pipe is at a point 540m distant from the pump and 45m higher in elevation. a. What is the velocity of flow on the discharge side of the pump? b. Assumingf= 0.025, compute the head loss of the pipe. c. Compute the pressure expected in the discharge pipe. 2 45 m 540m - 100mm dia
Water flow at a 250mm diameter horizontal pipe 90m long. The friction factor is 0.023. If the pressure at the starting point is 80KPA and the pressure at the end point is 50KPA. Determine the discharge at the pipe. A Q = 118.43 L/s В Q = 132.74 L/s Q = 101.07 L/s D Q = 172.81 L/s Q = 153.68 L/s No answer among the choices
8.2
A steel pipe is used to drain water from a reservoir that is 50 m above the datum, and water is discharged into the air at the elevation of the datum. The pipe is 1500 m long and 450 mm diameter and 50 mm wall thickness. A valve is installed at the downstream end of the pipe allows a flow rate of 0.71 m³/s. The valve was completely closed in 1.4 sec. Calculate maximum hammer pressure at the valve. The pipe is longitudinally anchored. Eb = 2.1×10° N/m², Ec=1.9×10¹¹ N/m².
v
Water at 20°C flows through a 300-mm-diameter pipe that discharg sphere as shown in Figure 4.61, When a partially open val the top of the pipe, the flow rate in the pipe is 0.2 m*s and the (gauge) pressure just upstream of the valve is 600 kPa. Estimate the force partially open valve, es into the atmo- ve extends 200 mm from exerted by the water on the —Valve 0.2 mYs —» Atmosphere Figure
The flowrate of the flow is 0.20 + a/10 m3 /s in a pipe placed on a horizontal plane. The pipe diameters are D1= 0.30 m and D2= 0.20. Please find the force acting to the pipe by the flow. The gauge pressure at (1) is p1 =200 + b*10 kN/m2 . (g=9,81 m/s2, g=10kN/m3 ) a= 4 b=3