A 48m distance from A to B on a level ground was paced by a civil engineer for the purpose of obtaining his pace factor. From the tabulated data shown, compute the pace factor. Trial Line No. of paces АВ 51.0 2 ВА 54.0 3 АВ 52.5 4. ВА 53.0

Q: in bullet form list structural work of beam

A: Structural work of beam

Q: What is the type of this truss

A: Solution: There are different types of trusses used in the construction field like Howe Trusses…

Q: match the following

A: Solution:- given following image is,

Q: Prepare the details estimate for the following 2 roomed building

A: In this question, we have to calculate the total estimate of works

Q: w H1 0.5 L 0.5L Figure 3 Activ. 6.2 Span "L" in metre Height (H1) in metre Live Load on the slab…

A: Strain energy hypothesis proposes that disappointment will happen when the strain energy per unit…

Q: Explain the minimum diameter of bar used in column ?

A: There are different shapes of bars are used in the construction. it is used to enhance the bond…

Q: Determine external indeterminacy

A: Given data : Number of external support reaction (R)=3+1+2=6

Q: Discuss Flexural Design Principles

A: The basic strength requirement for flexural design is  Mu≤ϕMnMn is the nominal moment strength of…

Q: Using virtual work methed Draw B.M.D2 4m

A:

Q: All specific sizes recommended by CRSI below meet minimum requirements of ACI 318 Recommended End…

A: The Standard Specifications require that reinforcing steel hooks and bends conform to the provisions…

Q: Problem 1 Wind blows on the side of a fully enclosed agricultural building located on an open flat…

A: When wind engineering is used to analyse tall buildings, the major load is frequently found to be…

Q: Problem 1-3: All stirrup information is provided, including spacing. You will find the resultant…

A:

Q: Draw shear force diagram

A: Finding support reaction at pinned support : Using equilibrium condition  Taking moment at point B…

Q: Describe about Rotational slides.

A: Slides refer to landslides, the movement of land mass is called a landslide. The mass of soil gets…

Q: draw stair tread and riser = 270 & 187 mm stair slab and landing thickness = 150 mm

A:

Q: Given: Diameter of pin at B = 20 mm Required: Shearing stress of the pin at B 40 kN A 35° Pin at B…

A:

Q: Define Allowable Stress Design

A: Their are mainly two type of design concept: Allowable stress method Load and resistance factor…

Q: What is the C or T, the X and Y components and the load of each member. Also can you put the answer…

A: Since the given truss is symmetric, half the truss is calculated.Using the method of joints:Joint…

Q: What is a contraction joint?

A: In the construction process, there are three types of joints. They are Contraction joint, Expansion…

Q: Appendix 1 shows a structural drawing of the first floor of a random building. The labels "C"…

A: Structural drawing for the first floor of the building C- Columns D1–4 is a 200 UB 29.8,3C–D is a…

Q: Select the correct statements regarding glulam layups for flexural and compression members.…

A: When used in heavy timber construction, Glulam ensures high earthquake resistance and excellent…

Q: QUESTION 12 List 2 methods that can be used to protect timber structural systems from termites. For…

A: Following are the two methods that can be used to protect timber from termites in Australia :

Q: 5. Among the following 3 choices, circle those choices where shear lag is an important factor in…

A:

Q: WOULD THE BEARINGS BE THE SAME?

A: Finding the bearings of a line AB, BC, CD, DA. In above solution find out the azimuth of lines is to…

Q: for 22 R 50 38 10 24 125 - 41 20 Drill 48 27 205 PROB. 7 METRIC. Hinged catch.

A:

Q: What is Spudding?

A: Spudding is defined as a process in which the drilling process of a well in any gas and oil industry…

Q: Make whatever changes or addition are necessary in each case to form a correct and complete FB.D.

A: 1) Incorrect, weight mg will act downwards 2) Incorrect, there will be frictional force acting at…

Q: When do shear plates become necessary?

A:

Q: Method of joints. AB, BD, BC

A: To find force in member AB,BD,BC

Q: Calculate P1, P2&P3 and Draw the S. F. D and B. M. D

A:

Q: Why is space filled with grout in this image necessary? Column Bar Plate Top Nut Grout Bottom Nut…

A: We know that grouting is generally used to fill the voids or  space between the two surfaces so that…

Q: draw a structural base in a picture

A: Structural layout shows the structural components of a building like beams & colums. This layout…

Q: Define Normal load,

A: The load that acts perpendicular to the contact surface is known as a Normal load. In  simple cases…

Q: 9. Write the deflection equation. Place your answer in a box. 10. What is the deflection at the pin…

A: Solution_1

Q: How i got shear force X zero point?

A:

Q: draw One-way slab- 12 mm diam. main bars spaced @        300 mm o.c. b/w with 10 mm diam. extra top…

A: Solution: Given: One-way slab: Main bars = 12 mm diameter Temperature bars = 10 mm diameter

Q: Draw a neat and clean diagram of the final configuration of how the bars are placed.

A: To draw the bar configuration of the given beam

Q: What is secondary compression?

A: Secondary compression:- It is a continuation of the volume change that started during primary…

Q: give illustration or drawing of a model of strong bridge that will use bbq stick and bands.

A: One of real life example of strong bridge having concept of bbq stick and bands is golden bridge…

Q: The vertical sides of a door and window openings provided in a wall are known as A) Verticals B…

A: Brief concept introduction- Verticals- These are the standard covering especially for glass doors.…

Q: raw concrete reinforced column with specifications and dimension

A: Column is the structural member that is used to transmit the load through compressive force from…

Q: Kindly provide a detailed solution for AB, AD, BC,BD

A: