A 480 volt 3-phase motor draws 375 amps of inrush current when started across the line and produces 250 % of normal full load torque. The starting current is 800% of the FLA rating of the motor. If using an autotransformer starter, determine the line inrush amps and motor amps for the 50%, 65% and 80% taps. (answer to 3 significant figures without units) 80% Tap I Inrush = Amps I Line = Amps 65% Tap I Inrush = Amps I Line = Amps 50% Tap I Inrush = Amps I Line = Amps

A 480 volt 3-phase motor draws 375 amps of inrush current when started across the line and produces 250 % of normal full load torque. The starting current is 800% of the FLA rating of the motor. If using an autotransformer starter, determine the line inrush amps and motor amps for the 50%, 65% and 80% taps. (answer to 3 significant figures without units) 80% Tap I Inrush = Amps I Line = Amps 65% Tap I Inrush = Amps I Line = Amps 50% Tap I Inrush = Amps I Line = Amps

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Kindly please solve what is ask. I want a complete and handwritten solution so that I can understand. Thank you!!'"
Q1/ A 380 volts 4 pole 60 Hz three phase star connected induction motor has r,=0, X1=X2=1 N, r2=0.4N, Xm= 500 N. The induction motor is fed from %D т i- A constant voltage source of 220 volts per phase and ii- A constant current source of 26 A. For both the cases calculate the slip at which maximum torque occurs and the starting and maximum torques.
53. A 200 W, 230 V, 50 Hz capacitor-start mo- tor has the following winding parameters: Main winding: R = 4·5 Q2 ; X₁ = 3·7 Q What should be the angle between input voltage and starting winding current to give maximum starting torque? (1) 38.2⁰ (iii) 50-4⁰ (ii) 24-6° (iv) 32.7°
Please answer in typing format
None
H2
The useful full load torque of a 3-phase 4 pole, 50 Hz induction motor is 162.84 lb-ft.The rotor e.m.f is observed to make 60 cycles per minute. Calculate Motor output Copper loss in rotor Motor input Efficiency if mechanical toque lost in windage and friction is 22.46 lb-ft and stator losses are 850 W
l7 answer 4 5 6
Question The power input to a 500 V, 50 Hz, 6-pole, 3-phase induction motor running at 975 RPM is 40 kW. The total stator losses are 1 kW. If the total friction and windage losses are 2.025 kW, then the efficiency is %
A 60 horsepower rated 230 V shunt motor has an armature circuit resistance of 0.052 ohm. The field resistance is 48.7 ohms. The motor is stated to have a maximum efficiency of 90.9%. Calculate the line current carried at maximum efficiency and the total stray power loss.
A 2 hp 50 Hz 3-phase 220 V delta wired induction motor has a full-load rated speed of 1400 rpm. a) How many poles does the motor have? b) Calculate its rated output torque. c) What is the slip at full load? d) If the current is 6.37 A with a power factor of 0.79 at full load, what is the efficiency of the motor? e) Calculate the torque and approximate speed at ½ load. f) If a variable frequency drive were used to control the speed of this motor, what is the approximate maximum speed for the load from e)? What frequency would the drive be set to? Please answer all subpart either dislike is ready please all subpart in short please
Problem 4 A460V, series motor runs at 500 rpm taking a current of 40A. Calculate the speed and percentage change in torque if the load is reduced so that the motor is taking 30A. Total resistance of armature and field circuit is 0.8 ohm.