A 480 V, 60 Hz, Y-connected six-pole synchronous generator has a per-phase synchronous reactance of 2.5 ohm. Its full-load armature current is 50 A at 0.75 PF lagging. The field current has been adjusted such that the no-load terminal voltage is 450 V. Calculate the i)torque angle 8. ii)Calculate the E iii)Active power. iv) Voltage regulation v) draw phasor

A 480 V, 60 Hz, Y-connected six-pole synchronous generator has a per-phase synchronous reactance of 2.5 ohm. Its full-load armature current is 50 A at 0.75 PF lagging. The field current has been adjusted such that the no-load terminal voltage is 450 V. Calculate the i)torque angle 8. ii)Calculate the E iii)Active power. iv) Voltage regulation v) draw phasor

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

23. As load is increased from no load to full load on a 3-phase squirrel-cage induction motor, what happens to the ..
13. A 250-V, 50-kW shunt generator has 1000 tuPAS ficld winding. On no load a current of 3'5 A in the field winding produces a terminal voltage of 250 V, but on full load the shunt current has to be increased to 5 A for the same terminal voltage at the same speed. Calculate the number of series field turns per pole required for level compounding.
A 420 Vdc, 8 pole Compound DC motor runs at 729 rev/min when drawing a load of 60 A from the supply when meeting a load demand of 28 kW. The compound motor has a Lap connected armature with 816 conductors. The Armature, Interpole, Series, and Shunt resistances are 0.295 Q, 0.0155 Q, 0.00118 Q, and 147 Q respectively. The series field has 6 turns per pole while the shunt field has 2800 turns per pole. Under full load conditions, the shunt current is 3.75 A, and the Friction and windage loss is Pf/w = 0.782 kW. Consider c =6 for lap winding. Assume constant shunt current and friction and windage loss, determine for a reduced output load of 14.5 kW; (a) The new armature current; (b) The new speed of the motor
A 1200 kVA, 6600 volts, three-phase wye connected alternator, has an effectiveresistance of 2.5 ohms and a reactance of 12 ohms per phase. Determine the inducedemf and the torque developed by the armature when fully loaded at 0.8 leading power factor.
A 13.8-kV, 50-MVA, 0.9-power-factor-lagging, 60-Hz, four-pole Y-connected synchronous generator has a synchronous reactance of 2.5 Q and an armature resistance of 0.2 2. At 60 Hz, its friction and windage losses are 1 MW, and its core losses are 1.5 MW. The field circuit has a dc voltage of 120 V, and the maximum Ir is 10 A. The current of the field circuit is adjustable over the range from 0 to 10 A. The OCC of this generator is shown in Figure P4-1. 4.2 Open-circuit characteristic 20 18 (a) How much field current is required to make the terminal voltage V, (or line voltage V,) equal to 13.8 kV when the generator is running at no load? 16 (b) What is the internal generated voltage E, of this machine at rated conditions? 14 12 (c) What is the phase voltage V of this generator at rated conditions? 10 (d) How much field current is required to make the terminal voltage V, equal to 13.8 kV when the generator is running at rated conditions? (e) Suppose that this generator is running at…
Solve it within 30 min I will upvote
Q2. a) A 415V, 50Hz, 3-phase induction motor supplies its rated power to a load. The rated speed of the motor is 980 rpm. b) Two synchronous generators, G2 and G2, are connected parallelly supplying a load. Generator G1 has a no-load frequency of 50.5 Hz and a slope of 300 MW/Hz. Generator G2 has a no-load frequency of 50.2 Hz and a slope of 500 MW/Hz. The load consumes 250 MW real power. (i) At what frequency does this system operate, and how much power is supplied by each of the two generators? (ii) An additional 100 MW load is added to this power system. What is the new system frequency, and how much power do G1 and G2 supply? (iii) The governor set point of G2 is changed to control system frequency back to 50 Hz. Determine the G2 governor set point.
A 15-kV 35-KVA 0.76-PF-lagging 50-Hz four-pole Y-connected steam-turbine generator has a synchronous reactance of 3.50 0 per phase and an armature resistance of 0.75 0 per phase. This generator is operating in parallel with a large power system (infinite bus). a) What is the magnitude of E, at rated conditions? b) What is the generator's torque angle at rated conditions? c) If the field current is constant, what is the maximum power possible out of this generator? How much reserve power or torque does this generator have at full load? d) Sketch the corresponding phasor diagram and calculate for the armature current (assume the field current is still unchanged) e) At the absolute power possible, how much reactive power will this generator be supplying or consuming?
Q/ dc shunt generator 4 pole with 500 condcutor , wave running at speed 1000 r.p.m the resistance of armature and field are 0.02 , 55 ohm and delivering load 43.12kwatt at terminal voltage 220 volt, the iron losses is 750 watt 1-Torque developed by the prime mover .........and The torque developed by the armature ........... when running at 1000 r.p.m * 2-The load current ,,,,,,,,,,,,when the speed drops to 800 r.p.m. if If is unchanged ? * 3-Output of the prime motor…….kwatt * 4-Mechanical , electrical and overall efficiency …….. * 5-Flux per pole is......... wb *
A 25 kW, 240 V self excited dc shunt generator has a field circuit resistance of 62.5 02, and an armature resistance of 0.05 Q. When delivering rated current at rated speed and voltage, calculate % Efficiency when rotational losses are 1200W, and iron losses are 600W. Note that Copper losses must be calculated too. No Units!
Terminal voltage of shunt G1 generator in idle operation is 500 V. The terminal voltage of the G1 generator drops to 470 V if it delivers a load current of 600 A. The idle operating voltage of the shunt G2 generator is 505 V. G2 generator terminal voltage drops to 470 V in case of 400 A load current. These two generators are connected in parallel to feed a load of 400 kW. Voltage-power characteristics of generators are linear. According to this; a. Draw the connection diagram given in the question. b. Obtain the network voltage and the powers of the generators. c. Calculate the current given by each generator to the load.
' A three phase, star connected, round rotor synchronous generator is rated 250 MW, 0.85 lagging power factor, 10.8 kV 50 Hz, and 1600 rpm. Each winding has an armature resistance of 1.5 mOHM and a synchronous reactance of 0.5 OHM 1)Determine the induced voltage for the condition of rated load and 0.85 power factor lagging. 2) Draw the phasor diagram with calculated values. 3) Determine the values of theta, gamma, delta, and torque angle