A 480-V, 50HZ, Y-connected, 6-pole synchronous generator has a per-phase synchronous reactance of 1.02. It's full load armature current is 60A at 0.8PF lagging. This generator has friction and windage losses of 1.5kW and core losses of 1.0kW at 60HZ at full load. Since armature resistance is being ignored, assume that l?R losses are negligible. The field current has been adjusted so that terminal voltage is 480V at no load. a) What is the speed of rotation of this generator? b) What is the terminal voltage at full load? What if the generator is then loaded with rated current at unity power factor? c) How efficient is this generator when it is operated at rated current at 0.8PF legaling? d) What is the voltage regulation of this generator at 0.8PF leading ?

A 480-V, 50HZ, Y-connected, 6-pole synchronous generator has a per-phase synchronous reactance of 1.02. It's full load armature current is 60A at 0.8PF lagging. This generator has friction and windage losses of 1.5kW and core losses of 1.0kW at 60HZ at full load. Since armature resistance is being ignored, assume that l?R losses are negligible. The field current has been adjusted so that terminal voltage is 480V at no load. a) What is the speed of rotation of this generator? b) What is the terminal voltage at full load? What if the generator is then loaded with rated current at unity power factor? c) How efficient is this generator when it is operated at rated current at 0.8PF legaling? d) What is the voltage regulation of this generator at 0.8PF leading ?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

13. A 250-V, 50-kW shunt generator has 1000 tuPAS ficld winding. On no load a current of 3'5 A in the field winding produces a terminal voltage of 250 V, but on full load the shunt current has to be increased to 5 A for the same terminal voltage at the same speed. Calculate the number of series field turns per pole required for level compounding.
Under short circuit, the reactance's of the synchronous generator during the steady state condition are following, Leakage reactance(X)= 0.15 ohm and Armature reactance (Xad) = 0.68 ohm The direct axis synchronous (steady state) reactance (Xa) is
A 10-kVA, 230-V, three-phase, delta-connected, the synchronous generator has a winding resistance of 0.2 ohms/phase and a synchronous reactance of 0.5 ohms/phase. Determine its voltage regulation when the power factor of the load is (a) 86.6% lagging, (b) 86.6% leading, and (c) unity.
A 40 MVA, 24-KV, 0.85-PF-lagging, 50-Hz, 4-pole, Delta-connected, 3- phase, steam-turbine generator has a synchronous reactance of 10 per- phase, and a negligible armature resistance. The field current is adjusted for 26-KV generator output line voltage at no load. This generator is connected to operate in parallel with a large power system (infinite bus). If the field current is unchanged, determine the absolute maximum output power of this generator. Select one: a. Pout, max = 187.2 MW b. Pout, max = 108 MW O c. Pout, max = 62.4 MW %3D O d. None
(021) Q21) A 5-k VA, 220-V, Y-connected, three-phase, salient-pole synchronous generator is used to supply power to a unity pf load. By means of a slip test, the direct-axis synchronous reactance is found to be 122 and the quadrature-axis synchronous reactance 792. Assume that rated current is delivered to the load at rated voltage and that armature resistance is negligible. (a) Compute the corresponding value of the excitation voltage. (b) What is the value of the internal phase displacement angle Y. (c) What is the value of the power angle? (d) Draw a carefully labeled phasor diagram. Q22) Repeat Prob.21 for the case where the load pf is 0.8 lagging. Q23) Repeat Prob.21 for the case where the load pf is 0.8 leading.
Please solve it quickly
Solve it within 30 min I will upvote
Energy Question-1) Three identical synchronous generators were connected in parallel and the idle frequency values of each generator were set to 54 Hz. The frequency - power characteristic slopes of the first and second generators are 5.3 MW/Hz and the slope of the third generator is 3.9 MW/Hz. When these three identical synchronous generators feed a load together, the system frequency becomes f=51.7 Hz. According to this;a-) Calculate the active power value that the first generator will provide to the load.b-) Find the active power that the second generator will provide to the load.c-) Find the active power that the third generator will provide to the load.d-) Calculate the power of the load.(All values in options a, b, c, and d in this Question will be entered as two digits after the comma.) NOTE: If the information in the text and the photo is different, please solve the question using the information given in the photo. Help me please... Thank you so much.
Terminal voltage of shunt G1 generator in idle operation is 500 V. The terminal voltage of the G1 generator drops to 470 V if it delivers a load current of 600 A. The idle operating voltage of the shunt G2 generator is 505 V. G2 generator terminal voltage drops to 470 V in case of 400 A load current. These two generators are connected in parallel to feed a load of 400 kW. Voltage-power characteristics of generators are linear. According to this; a. Draw the connection diagram given in the question. b. Obtain the network voltage and the powers of the generators. c. Calculate the current given by each generator to the load.
Three identical steam-turbine generators G1, G2, and G3 are operating in parallel. Each generator is: 7.2 KV, 25.4 MVA, 60 Hz, 0.77 PF lagging, 4-poles, Y-connected, with synchronous reactance of 2 Q and an armature resistance of 0.05 Q. Each of generators G¡ , and G2 has a characteristic power-frequency slope of 5.8 MW/Hz, and no-load frequency of 62.5 Hz. Generator G3 has a characteristic power-frequency slope of 6.0 MW/Hz. Find the no-load frequency of generator G3 for which all generators supply a load of 38.5 MW, at fsys = 60 Hz. Select one: O a. fsys = 62.5 Hz O b. fsys = 61.85 Hz O c. None O d. fsys = 61.58 Hz Clear my choice
Please i want the answer son as possible