Example 12.2A 4.16 kV three-phase feeder is supplying a purely resistive load of 5400 kVA. It has been deter-mined that there are 175 V of zero-sequence third harmonic and 75 V of negative-sequence fifthharmonic. Determine the following:a. The total voltage distortion.b. Is the THD below the IEEE Std. 519-1992 for the 4.16 kV distribution system?

The solution can be achieved as follows.

Answered: A 4.16 kV three-phase feeder is…

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.20MCQ

See similar textbooks

Similar questions

In per-unit equivalent circuits of practical three-phase transformers, under balanced thr-phase operation, in which of the following connect ions would a phase-shifting transformer come up? (a) Y-Y (b) Y- (c) -
Power in a three phase delta system with balanced load is equal to (Sqrt (3)) (VL) (IL) (p.f.) (Sqrt (3)) (Vph) (Iph) (p.f.) (Sqrt (3)) (VL) (Iph) (p.f.) O (Sqrt (3)) (Vph) (IL) (p.f.)
No-load operation and short circuit tests were performed on three-phase, 50 Hz 480/220 delta / Y connected transformer. In these testsThe line voltage, line current and three-phase total power have been measured from the high voltage windings and the test results are below.pictures. 100 A DC current when 1.08 V DC voltage from non-transferable software is applied to the low voltage windingshas attracted.Find the single phase equivalent circuit parameters of this transformer.idle test:Voltage: 480V Power:114w current: 0.71Ashort circiut test:V: 10v P: 78w c: 18.3a
Find the following : 1.Ripple Voltage (vpp) 2. Zero-to peak ripple(Vop) 3.secondary winding of the transformer high line and low line
A 10 MVA three phase load is to be served by a three phase transformer at aline voltage of 13.8 kV. The supply side voltage(line-line) is 138 kV. Varioussingle phase transformers are available in the warehouse but all havewindings with voltage ratings under 100 kV and current ratings under 250 A.Is it possible to serve the load using only three single phase transformers? Ifso, specify the three phase connections and the low and high voltage ratingsof the single phase transformers.
A 50 Hz, Scott connected transformer supplies an unbalanced two phase load at ( 400 V) per phase. For the leading phase the load has a resistance of (13.3 ohm) and capacitor of (318) micro farad in series. For the other phase the load consists of resistance (10) ohm and an inductance of (42.3) mH. Calculate both mathematically and graphically the lines currents on 3- phase side. The main transformer primary to secondary turns ratio is (12/1).
A 50 Hz, Scott connected transformer supplies an unbalanced two phase load at ( 400 V) per phase. For the leading phase the load has a resistance of (13.3 ohm) and capacitor of (318) micro farad in series. For the other phase the load consists of resistance (10) ohm and an inductance of (42.3) mH. Calculate both mathematically and graphically the lines currents on 3-phase side. The main transformer primary to secondary turns ratio is (12/1).
Three single-phase two-winding transformers, each rated 25MVA,54.2/5.42kV, are connected to form a three-phase Y- bank with a balanced Y-connected resistive load of 0.6 per phase on the low-voltage side. By choosing a base of 75 MVA (three phase) and 94 kV (line-to-line) for the high-voltage side of the transformer bank, specify the base quantities for the low-voltage side. Determine the per-unit resistance of the load on the base for the low-voltage side. Then determine the load resistance RL in ohms referred to the high-voltage side and the per-unit value of this load resistance on the chosen base.
The ratings of a three-phase, three-winding transformer are Primary: Y connected, 66kV,15MVA Secondary: Y connected, 13.2kV,10MVA Tertiary: connected, 2.3kV,5MVA Neglecting resistances and exciting current, the leakage reactances are: XPS=0.09 per unit on a 15-MVA,66-kV base XPT=0.08 per unit on a 15-MVA,66-kV base XST=0.05 per unit on a 10-MVA,13.2-kV base Determine the per-unit reactances of the per-phase equivalent circuit using a base of 15 MVA and 66 kV for the primary.
A bank of three single-phase transformers, each rated 30MVA,38.1/3.81kV, are connected in Y- with a balanced load of three 1, Y-connected resistors. Choosing a base of 90MVA,66kV for the high-voltage side of the three-phase transformer. spify the base for the low-voltage side. Compute the per-unit resistance of the load on the base for the low-voltage side. Also, determine the load resistance in ohms referred to the high-voltage side and the per-unit value on the chosen base.
Three single-phase, two-winding transformers, each rated 450MVA,20kV/288.7kV, with leakage reactance Xeq=0.10perunit, are connected to form a three-phase bank. The high-voltage windings are connected in Y with a solidly grounded neutral. Draw the per-unit equivalent circuit if the low-voltage windings are connected (a) in with American standard phase shift or (b) in Y with an open neutral. Use the transformer ratings as base quantities. Winding resistances and exciting current are neglected.
Consider a bank of this single-phase two-winding transformers whose high-voltage terminals are connected to a three-phase, 13.8-kV feeder. The low-voltage terminals are connected to a three-phase substation load rated 2.0 MVA and 2.5 kV. Determine the required voltage, current, and MVA ratings of both windings of each transformer, when the high-voltage/low- voltage windings are connected (a) Y-, (b) -Y, (c) Y-Y, and (d) -.

SEE MORE QUESTIONS

Recommended textbooks for you

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning