A 4-pole, 500 V d.c. shunt motor has 720 wave-connected conductors on its armature. The full-load armature current is 60 A and the flux per pole 0.03 Wb. The armature resistacne is 1.2 02. What is the full-load speed of the motor a. 675 rpm b. 678rpm c. 665 rpm d. 658 rpm

Q: A 6 pole, DC generator has a wave-wound armature containing 30 coils of 5 turns each. Its flux per…

A: Given- Number of poles P=6, DC generator- wave-wound armature, 30 coils of 5 turns each, Number of…

Q: 4. A three-phase A-connected six-pole winding is installed in 36 slots on a stator. There are 150…

A: Introduction A three-phase delta-connected system is a type of electrical power distribution…

Q: 4-pole, wave-wound armature has 72 slots with two coil-sides per slot, each coil has four turns. If…

A:

Q: What is the freq. of a 10-pole alternator when running at 360 rpm? (b) At what speeds should a…

A:

Q: A DC generator has 4 pole, wave wound amature with 736 conductors. If the induced voltage in the…

A: According to the question we have to find the value of flux per pole.

Q: Name the principal parts of a rotating electrical machine

A: Any electrical machine has divided into mainly two parts one is stator part and another is rotor…

Q: A 4-pole wave-wound motor is connected to a 406 V d.c. supply. The armature has 479 conductors and a…

A:

Q: Armature reaction in an alternator primarily affects

A: Conceptual Background:- Armature Reaction:- Simply put, the armature reaction depicts how the…

Q: A wave wound armature of an eight-pole DC shunt generator has 51 slots, each

A:

Q: 7- Iron loss in the rotor of a 3-phase induction motor (a) Very low frequency of emf induced in the…

A: In this question,  We need to choose the correct options Iron losses in the rotor of the 3 phase…

Q: .A 230 V dc series motor has Ra=0.22, Rf=0.12. The motor draw 40A at rated speed and 1000 RPM. Find…

A:

Q: The factors effecting the speed of dc motor are The flux p and the voltage across the armature The…

A: The factor affecting the speed of the dc motor is as follows; N=V-Ia RaϕN= speed of dc…

Q: Q25) i) What are the factors that the induced voltage in three phase induction motor depends upon…

A: Factors that the induced voltage in three phase induction motor depends upon : 1. Magnitude of…

Q: what is the conclusion for the concepts of rotating amature and rotating field in an alternator?

A: There are two types of alternators are used one is rotating armature type and the other one is…

Q: 16 A 2-pole d.c. shunt generator has a useful flux per pole of 0.03 Wb. The armature winding consist…

A: DC shunt generator No of pole 2 Speed N= 1200 rpm Flux per pole 0.03 No of turns 200 No of…

Q: 93. A 4-pole de generator runs at 1500 rpm. The frequency of current in armature winding is (a) Zero…

A: Given, Total number of pole, P = 4. Speed, N = 1500 rpm.

Q: 1. The operation of Commutator in DC Motor is O a) to convert dc to ac O b) to convert ac to dc O c)…

A:

Q: Maximum torque is realized when an armature winding is with the magnetic field at 90° O inline or at…

A: With reference to synchronous machines, the load angle or the power angle is the angle between the…

Q: The voltage induced by a 6-pole DC generator running at 600 [RPM] with 100 slots on the armature and…

A: Given,  A DC generator has,  Number of poles,  p = 6  Speed of rotor,  N = 600 rpm  Flux per pole =…

Q: Differentiate the two generators shown in Figure 1.6.1-1 and Figure 1.6.1-2. The output voltage can…

A: Consider the first generator: This is a permanent magnet generator that is a machine that changes…

Q: The DC shunt generator with the terminal voltage 300 V, armature drop 9 V and the total brush drop 4…

A: Given: DC Shunt generator, Terminal voltage, Vt = 300V Armature drop, Ia.Ra = 9 V Total brush drop,…

Q: The armature of a shunt generator has 0.05 ohm effective resistance. Each brush has an effective…

A: It is given that: Ra=0.05 ΩRb=2×0.01 Ω=0.02 ΩVt=100 VIL=40 A

Q: In a given DC motor, the output power is 20 HP, and the rotational losses are 1.1 KW. If the motor…

A:

Q: A four-pole induction motor drives a load at 2478 rpm. This is to be accomplished by using an…

A: speed of the induction motor    Nr = 2478 rpm dc voltage  V = 400 V  number of poles P= 4  slip =…

Winding and Constructions

Alternating Current (AC) winding is generally of the 3-phase type due to the inherent advantages of the 3-phase machine. Armature coils must be connected to the yield balance (equivalent in magnitude and 2/3 of the series phase difference of the rod) 3-phase electromotive forces (emf). The armature should be divided into step-bands to start with slots around the perimeter.In the construction of AC machines, the frame is used as an external protective shield to protect it from environmental conditions. The frame also serves as the outer perimeter, allowing the interior to be easily placed. The static state section of the devices is the stator winding attached stator.