A 380-L tank contains steam, initially at 440°C, 3 bar. A valve is opened for 10 seconds and steam flows out of the tank at a constant mass flow rate of 0.005 kg/s. During steam removal, a heater maintains the temperature within the tank constant. Determine final mass remaining in the tank, in kg, and the final pressure in the tank, in bar.

A 380-L tank contains steam, initially at 440°C, 3 bar. A valve is opened for 10 seconds and steam flows out of the tank at a constant mass flow rate of 0.005 kg/s. During steam removal, a heater maintains the temperature within the tank constant. Determine final mass remaining in the tank, in kg, and the final pressure in the tank, in bar.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q3: A certain fluid at Pressure of 6 bar, and with a specific volume of 0.12 m³/kg. Contained in a cylinder behind a piston expands reversibly to a pressure of 1.5 bar according to law P= V2.5 Where c is constant. Calculate the work done during the process.
Refrigerant 134a enters an insulated compressor operating at steady state as saturated vapor at -26°C with a volumetric flow rate of 0.18 m3/s. Refrigerant exits at 7 bar, 70°C. Changes in kinetic and potential energy from inlet to exit can be ignored. 1.Determine the volumetric flow rate at the exit, in m3/s 2. Determine the compressor power, in kW.
Air within a piston–cylinder assembly, initially at 50 lbf/ in.2, 510°R, and a volume of 6 ft3, is compressed isentropically to a final volume of 0.5 ft3. Assuming the ideal gas model with k = 1.4 for the air, determine the: (a) mass, in lb. (b) final pressure, in lbf/in.2(c) final temperature, in °R.(d) work, in Btu.
Water contained in a closed, rigid tank, initially at 100 lb/in², 800°F, is cooled to a final state where the pressure is 25 lb/in². Determine the quality at the final state and the change in specific entropy, in Btu/lb-ºR, for the process.
A reheat cycle with two stages of reheating is executed with steam expanding initially from 25 MPa and 600 °C. The two reheater pressures are 4 MPa and 1 MPa, and the steam leaves each reheater at 600 °C. Condensation occurs at 40°C. For 1 kg/s of steam, what is QA in kW? Remember, 1. For values taken from the steam tables: Use them as is, do not round off. 2. For values obtained by interpolation and final answers obtained by solving, use FOUR (4) decimal places. 3. Use the steam tables provided
10- 1 kg of Nitrogen at 150 °C and 5 bar, undergoes the following sequences of reversible processes in a piston cylinder arrangements: a- An adiabatic expansion in which the volume is doubled. b- A constant pressure process in which the volume is reduced to its initial value. A constant volume process back to the initial state. C- Calculate the net work done of this cycle.
13
Refrigerant 134a at p1 = 30 lbf/in2, T1 = 40°F enters a compressor operating at steady state with a mass flow rate of 350 Ib/h and exits as saturated vapor at p2 = 16O Ib/in?. Heat transfer occurs from the compressor to its surroundings, which are at To = 40°F. Changes in kinetic and potential energy can be ignored. The power input to the compressor is 3.5 hp. Determine the heat transfer rate for the compressor, in Btu/hr, and the entropy production rate for the compressor, in Btu/hr.°R.
1. A tank containing 250 kg of kerosene is to be heated from 20°C to 40 °C in 15 minutes, using 4 bar steam. The kerosene has a specific heat capacity of 2.0 kJ/kg-°C.over that temperature range. ha at 4.0 bar is 2,108.1 kJ/kg. The tank is well insulated and heat losses are negligible. Determine the rate of heat transfer required and steam flow.
13
Air enters the cylinder of a 4-stroke gasoline engine at 33°C and 101.2 kPa. Engine clearance is 10.5% of the displacement. 2600 kJ/kg of heat is added during the constant volume heat addition process. Determine the following:a. Pressure & Specific Volume at each state.b. Work per unit mass (using volume and pressure).
Calculate the energy requirement to raise the temperature of 1 kg of water from 60 ° C of water to 90 ° C using the following approach; a. Average specific heat usage (Tab A Singh's Book. 4.1) = kJ b. The enthalpy change in the water - vapor saturation table (Tab A Singh's Book. 4.2) = kJ