A 360UB56.7 grade 300 steel beam is supporting two equal point loads as shown in figure below. The beam is restrained against twist and lateral movement at the two locations where the loads are applied and at the supports. The beam may be assumed to be simply supported. What is the maximum design load P* that can be carried by this beam? P* P* 2m 4m 2m

A 360UB56.7 grade 300 steel beam is supporting two equal point loads as shown in figure below. The beam is restrained against twist and lateral movement at the two locations where the loads are applied and at the supports. The beam may be assumed to be simply supported. What is the maximum design load P* that can be carried by this beam? P* P* 2m 4m 2m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

AW14 x 43 column in a braced frame has a yield stress of 50 ksi and a height of 10 ft. The column is pinned at the top and bottom and has no intermediate bracing. Determine the available strength of the column considering the critical stress for flexural buckling. From AISC Manual Table 1-1, the properties of a W14 x 43 are: A = 12.6 in^2 tw = 0.305 in bf/2tf = 7.54 h/tw = 37.4 rx = 5.82 in ry = 1.89 in Ix = 428 in4 ly = 45.2 in4 G= 11,200 ksi J = 1.05 in^4 Cw=1950 in^6 What is the nominal axial strength considering flexural buckling stress of the column section (in kips). O 310 O 468 O 447 O 375 O 420 O 436 O 517 O 280
A cantilever beam having a 4m span carries a uniformly distributed load throughout its length. The beam is A36 steel with yield strength Fy = 248 MPa. The beam is not restrained against lateral buckling. The beam is W 21 by 62 steel shape, whose relevant properties are shown below: r = 0.053 m d = 0.533 m bf = 0.210 m tf = 0.016 m S = 0.002077 m3 Given this condition, solve for the allowable flexural stress in the compression flange. Use Cb = 1 as should be taken conservatively
i need the answer quickly
A lightly welded steel beam shown in Figure 5 is continuously supported along its length. A downward concentrated load of 4P acts at Point C, and two downward concentrated loads P act at Points A and E. The beam with full lateral restraint is bent about its major principal x-axis. Determine the followings: a. Section type based on section slenderness; b. Effective section modulus; c. The maximum design value of P. A k B fu 6 m d tw bf 6 m tf 4P d bf tw tf = - = fyf= fyw 6 m D um * 550 mm 206 mm 6 mm 10 mm 320 MPa = 340 MPa Zx=1362985 mm³ Sx 1533750 mm³ Figure 5 Steel beam under design loads. 6 m P E
I need the answer as soon as possible
The answer is between 18.25 and 20.25
Determine the maximum load that an 8 foot long 2"x4" rectangular aluminum alloy bar (E = 10.5x10^3ksi, σY = 40 ksi) can support with a factor of safety of 3 for both crushing and buckling if it has endconditions of:a. Pinned-pinned.b. Pinned-fixed.c. Fixed-free.d. Fixed-fixed.
plss, i need the answer immediately!
Please answer with each steps.
Give me right solution with clear calculations step by step. If you don't know the solution please leave it but don't give me wrong solution
steel The hollow section column, shown in the figure below, has a length of 18 ft, and it is made of steel with a yield strength of 50 ksi. The column is fixed at the bottom and pinned at the top. What is the capacity of this column under a pure compressive loading? |3/4 in 3/4 in 10 in 5 in
A frame structure is shown below. The links connected below is a bar with a 30mm by 60mm in section. Find the Allowable lad P that can be applied so that the stresses will not exceed 100MPa in tension or 80Mpa in compression.