A 35.2 HP, 250 V, 100 A, 1200 RPM, series DC motor with no armature reaction is considered inthis problem.This motor has a series-field winding of 5 turns per pole. Its armature resistance in RA=0.05 92, andits series field resistance is Rs = 0.05 2.The magnetization curve at 1200 RPM is given by the following table:EA (V)F(Amp.turns)50 95 125 150 180200 500 7551000 1280 1500200 212 229 243 250 2532000 2500 3000 3500 4000The motor is operating at rated voltage, armature current of 100 Amperes, and with rotational lossesof 1500 Watt.Find the speed of the motor.Select one:O a. Speed 1200 RPMO b. Speed n = 475 RPMO c. Speed n = 3032 RPMO d. None

Answered: Image /qna-images/answer/a1491b91-04dd-4aac-914b-b06bda21ee29.jpg

A 35.2 HP, 250 V, 100 A, 1200 RPM, series DC motor with no armature reaction is considered in this problem. This motor has a series-field winding of 5 turns per pole. Its armature resistance in RA=0.05 S2, and its series field resistance is Rs = 0.05 52. The magnetization curve at 1200 RPM is given by the following table: EA (V) F (Amp.turns) 50 95 125 200 500 755 150 180 200 212 229 243 250 253 1000 1280 1500 2000 2500 3000 3500 4000 The motor is operating at rated voltage, armature current of 100 Amperes, and with rotational losses of 1500 Watt. Find the speed of the motor.

A 35.2 HP, 250 V, 100 A, 1200 RPM, series DC motor with no armature reaction is considered in this problem. This motor has a series-field winding of 5 turns per pole. Its armature resistance in RA=0.05 S2, and its series field resistance is Rs = 0.05 52. The magnetization curve at 1200 RPM is given by the following table: EA (V) F (Amp.turns) 50 95 125 200 500 755 150 180 200 212 229 243 250 253 1000 1280 1500 2000 2500 3000 3500 4000 The motor is operating at rated voltage, armature current of 100 Amperes, and with rotational losses of 1500 Watt. Find the speed of the motor.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 4-pole series motor has 800 lap connected armature conductors. At a certain load, the flux per pole is60mWb and the total mechanical torque developed is 400 N-m. Calculate the line current taken by themotor and the speed at which it will run with a back emf of 400 V. Total motor resistance is 4 ohm.
Speed control of a 140 V, 1.68 kW DC motor single phase thyristor full wave AC-DC It is made by the converter. AA supply voltage 220 V (rms) Is 50. In the converter It is assumed that there is no loss. The armature resistance of the DC motor is = 0.417 Q. Very a large inductance is connected in series with the motor. The motor voltage constant is = 0.0964 V/rpm. The motor can be considered as a permanent magnet DC. According to this, a) Draw the driver (converter-motor) power circuit. b) Calculate the nominal current of the motor. c) Supply voltage, supply current, converter output voltage for ignition angle a = 30 ° and Draw the waveforms for the converter output current. d) = 950 rpm and for nominal current, d1) The firing angle of the converter, d2) Effective value of supply and thyristor current, d3) Supply power factor, calculate.
A dc shunt motor developes 10 HP at 8000 rpm when drawing a line current of 40 A at 220 V. Find the efficiency at this load and the useful torque.
current - 1=?, and the power factor - cosp =?. 4. An out of balance three phase star connected load has the following complex currents: I₁ = lejº,A, I₂ =le¯6⁰,A and I₁=1e¹j6⁰, A. This load is supplied by a four wire power line from a balance voltage source. Find the r.m.s. value of the neutral current Io =? Wait to th
A D.C. series motor of resistance 1 ohm between terminals runs at 800 r.p.m. at200 V with a current of 50 A. Find the speed at which it will run when connectedin series with a 5 ohms resistance and taking the same current.
A DC motor with a shunt field winding has the following characteristics: Vr = 96.0 V R = 1.50 Q K = 0.352 m Specify the flux required to achieve a starting torque of 18 Nm.
A 3-phase 50 Hz I.M. has a rated torque = 16.7 N.M and maximum torque = 40.5 N.M. If its rated speed = 910 R.P.M, the speed at :maximum torque will be R.P.M 578.280 R.P.M 421.640 R.P.M 590.160 None O
The relation between armature torque and armature current of a DC motor is Parabolic Linear Inverse Exponential
3. A 4 pole, 250 dc shunt motor has a lap connected armature with 960 conductors. The flux per pole is 2 x 102Wb. Calculate the torque developed by the armature and the useful torque in N-m when the current taken by the motor is 30A. The armature resistance is 0.12 ohm and the field resistance is 125ohm. The rotational losses amount to 825W
Developed torque??
a 220 V dc shunt motor has armature resistance 0.23 ohm, on load it takes armature current 40 A and turnes at 720 rpm, if the flux of motor is reduced by 10% without changing the load torque . Find the new speed of the motor.