A 30 m. tape was standardized and was found to be 0.0022 m. too long than the standard length at anobserved temperature of 55 deg Celcius and a pull of 15 kg. The same tape was used to measure a certaindistance and was recorded to be 670.89 m. long at an observed temperature of 64 deg Celcius and a pull of15 kg. Coefficient of linear expansion is 0.0000116/deg Celcius. a.Determine the true length of the line. b.Determine the total correction.  c. Determine the correction due to temperature.

Q: 8. An inflatable structure used by a traveling circus has the shape of a half-circular cylinder with…

A:

Q: For a solid circular shaft with diameter 19.31mm, estimate the value of the polar moment of inertia…

A: Given data- Diameter of circular shaft(d) = 19.31mm

Q: ANALYSE THE FRAME BY MOMENT DISTRIBUTION METHOD

A: Consider the free body diagram of given sway frame with externally applied force X at point C in…

Q: 12. During a weak jump, the value of Froude lies in between a) 1 to 2.5 b) 2 5 to 35

A: To find : Value of Froude's number.

Q: Problem 5. Calculate the maximum safe magnitude of M considering the following data and figure shown…

A: Given  Length of copper= 160 mm  Length of steel= 240 mm

Q: HW. For the figure below fined the temperature of the nodels 1 to 9. 2 cm h, T= 50°C 4 1 cm T= 300°C…

A: A Fourier transform system is a way of calculating points in a system area with the correct…

Q: To damp oscillations, the pointer of a galvanometer is fixed to a circular disk which turns in a…

A: Given data,  ω= 0.30 rad/s  Viscosity of oil = 8x10^-3 Pa-s Disc diameter = 75 mm Oil gap = 0.5mm…

Q: Figure P9-84 represent the steel shaft of a machine. The gears mounted on the arrow produce the…

A:

Q: Please don't use Chatgpt will upvote and give handwritten solution

A: Step 1: Step 2: Step 3: Step 4:

Q: It is required to determine the height oftwo concentric cylinders used to construct a rotational…

A:

Q: Strength of material Deflection Measurement for Simply Supported Beam

A: AIM : To calculate the deflection of a simply supported beam with point load at the centre of the…

Q: The 20kg box represented in the illustration is moved on a stage which is attached to two equal,…

A: horizontal and vertical equilibrium equation to find normal reaction and frictional force static…

Q: Determine the resultant of the three forces shown in the figure.

A: Answer To calculate the resultant of the given 3 forces we have Resultant  = ∑Fx2+∑Fy2 where ∑Fx =…

Q: The beam as shown is used in a building subjected to two different thermal environments. If the…

A: It is required to determine the vertical deflection of the beam at its midpoint using the relation.…

Q: A 50-m tape of standard length has a mass of 0.05kg/m, with a cross-sectional area of  0.04 sq. cm.…

A: True length : Any distance between points that are not foreshortened by the view type is referred to…

Q: A vibrating system is characterised by the following parameters: Mass = (m) = 6 kg Stiffness of…

A:

Q: Find the temperature distribution equations, using the separation of variables method, for a…

A: ## Step 1: Governing Equation and Separation of VariablesThe heat transfer within the plate is…

Q: 20.11 kN 20.11 kN 3.98 m 3.98 m 3.98 m C. D. 3.98 m 3.98 m

A:

Q: A vibration test was conducted on the model of a tank. A cable attached to the tank induced a force…

A:

Q: A 1.25 m long steel rod is rigidly supported at its base and is free to expand 1 mm before making…

A:

Q: Q3. When a fluid flows over a surface, the shear stress 7 (N/m²) at the surface is given by the…

A: Y01234u055.5688.89100111.56.at surface y=0.

Q: A line was determined to be 2395.25 m when measured with a a 30-m steel tape supported throughout…

A:

Q: (El) Beam = 5000 kNm² 2m B K-1000 N/m m) 50 kg The fundamental time period of vibration of the…

A:

Q: The beam AB in the Figure supports a load which varies an intensity of 220 N/m to 890 N/m. Calculate…

A:

Dependence on mechanical properties

The mechanical properties of materials are those structures that include the reaction to the load used. Metal switching features determine the scope of the usefulness of the content and establish the expected service life. Machine structures are also used to help distinguish and identify material objects. The most common mechanical properties considered are strength, ductility, stiffness, impact resistance, and resilience to fractures.