A 30-m steel tape standardized at 20°C and supported throughout under a tension of 5.45 kg was found to be 30.012-m long. The tape had a cross-sectional area of 0.050 cm? and a weight of 0.03967 kg/m. This tape was held horizontal, supported at the ends only, with a constant tension of 9.09 kg, to measure a line from A to B in three segments. The following data below were gathered from the field. Measured Temperature Section Distance (m) ("C) А-1 30 14 1-2 30 15 2-B 21.151 16

A 30-m steel tape standardized at 20°C and supported throughout under a tension of 5.45 kg was found to be 30.012-m long. The tape had a cross-sectional area of 0.050 cm? and a weight of 0.03967 kg/m. This tape was held horizontal, supported at the ends only, with a constant tension of 9.09 kg, to measure a line from A to B in three segments. The following data below were gathered from the field. Measured Temperature Section Distance (m) ("C) А-1 30 14 1-2 30 15 2-B 21.151 16

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Getting measurements from Figure , determine approximate values of the following items for steel with different carbon contents. Use one system of units only as specified by the instructor.a. Yield stressb. Ultimate strengthc. Strain at failured. Effect on modulus of elasticitye. Approximate toughness. Curves may be approximated with a series of straight lines.f. Comment on the effect of increasing carbon content on items a through e above.
The rigid bar of negligible weight is supported as shown in the figure. If W=80 kN, compute the temperature change of the assembly that will cause a tensile stress of 50 MPa in the steel rod. Use the following data:
With illustrations please and detailed Solution.
(40 How A Rismatic steel bar of a Square cro ss section (looxlo0)mm is loaoled by Compressive force P= 1300 K, the bar has length 2.5 m, Eg=200GPay V=0.3,determine the shortening 8, the increase in the dimensions of cross Section, the change in Volume DV of the bar? loomm loomm
The solid rod has a diameter of 20mm. Find the following: Angle of twist at C with respect to A (in radians) Angle of twist at B with respect to A (in radians) Maximum shear stress at A (in MPa) (Shear stress at support, at a point 7mm from center. (in MPa) A-36 steel with the following properties: Modulus of Elasticity, E = 29x10^3 ksi or 200 GPa Shear Modulus/Modulus of Rigidity, G = 11.5x10^3 ksi or 79.3 GPa Poisson's Ratio, nu = 0.260 Temperature Coefficient for thermal expansion, a = 6.6x10^-6/°F or 11.7x10^-6/°C
Determine the following: Displacement of B (in mm) with respect to A. Displacement of C (in mm) with respect to A. Principal stresses at point O, if it is 200mm from C. (unit should be kPa). A-36 steel with the following properties: Modulus of Elasticity, E = 29x10^3 ksi or 200 GPa Shear Modulus/Modulus of Rigidity, G = 11.5x10^3 ksi or 79.3 GPa Poisson's Ratio, nu = 0.260 Temperature Coefficient for thermal expansion, a = 6.6x10^-6/°F or 11.7x10^-6/°C
Topic: Stresses in Beams (Given formulae: Fb =Mc / I for bending stress v = VcA' y' / Ib for Shear stress)
Kindly include the diagram. Handwritten solution recommended.
pls help me. thank u refer to the picture attached below.
Determine the following for the bar. A) B) C) D) σ, ksi 100 ksi 80 ksi T, ksi 40 ksi What is the Modulus of Elasticity for the material of the bar. What tensile force will cause the bar to yield? What will be the length of the bar after a 540 kip force is applied? What will be the cross sectional dimensions after a 300 kip force is applied? 0.0025 0.0035 0.0095 0.0100 0.0130 0.0145 Y, radians ɛ, in/in 20 in 3 in Cross Section 2 in
Read the question carefully and give me both right solutions with clear explanation. Don't copy from other websites solution