A 30-kg disk A is attached to one end of a spring with stiffness k = 200 N/m at its center G. The other end of the spring is fixed at A. The disk is initially at rest with the spring unstretched. A couple moment of M = 80 Nm is then applied to the disk causing the disk to roll to the left without sliding. Consider the duration of motion when the disk rolls from the position shown (Position 1) to a position (Position 2) when its mass center G has moved 0.5 m to the left. M = 80 Nm 0.5 m k = 200 N/m 3. Which of the following gives the closest value of the work done by the spring from position 1 to position 2? 4. Which of the following gives the closest value of the work done by the applied couple from position 1 to position 2? -80 Nm -40 Nm 40 Nm 80 Nm ◆ A O 25 Nm -25 Nm 50 Nm -50 Nm ◆

A 30-kg disk A is attached to one end of a spring with stiffness k = 200 N/m at its center G. The other end of the spring is fixed at A. The disk is initially at rest with the spring unstretched. A couple moment of M = 80 Nm is then applied to the disk causing the disk to roll to the left without sliding. Consider the duration of motion when the disk rolls from the position shown (Position 1) to a position (Position 2) when its mass center G has moved 0.5 m to the left. M = 80 Nm 0.5 m k = 200 N/m 3. Which of the following gives the closest value of the work done by the spring from position 1 to position 2? 4. Which of the following gives the closest value of the work done by the applied couple from position 1 to position 2? -80 Nm -40 Nm 40 Nm 80 Nm ◆ A O 25 Nm -25 Nm 50 Nm -50 Nm ◆

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The 29-kg wheel is rolling under the constant moment of M = 85 N·m. The wheel has radius r = 0.57 m, has mass center at point G, and the radius of gyration is kg = 0.25 m. The coefficients of friction between the wheel and the ground is g = 0.37 and μk = 0.16. If the wheel rolls while slipping, determine the magnitude of the linear acceleration of point G (in m/s²). Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point. Take g = 9.81 m/s². M Your Answer: Answer
The 16-kg wheel is rolling under the constant moment of M = 60 N-m. The wheel has radius r= 0.50 m, has mass center at point G, and the radius of gyration is kg = 0.23 m. The coefficients of friction between the wheel and the ground is ls = 0.28 and Uk = 0.14. If the wheel rolls without slipping, determine the angular acceleration of the wheel (in rad/s?). Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point. Take g = 9.81 m/s?. M
The system is at rest with the spring unstretched when theta = 0. the 5.3 kg uniform slender bar is then given a slight clockwise nudge. The value of b is 0.45 m. (a) if the bar comes to momentary rest when theta = 58, determine the spring constant k. (b) for the value k = 65 N/m, find the magnitude of the angular velocity of th ebar when theta = 38 degrees.
The 30-kg wheel is rolling under the constant moment of M = 84 N.m. The wheel has radius r = 0.48 m, has mass center at point G, and the radius of gyration is kg = 0.24 m. The coefficients of friction between the wheel and the ground is μ = 0.39 and k=0.10. If the wheel rolls without slipping, determine the angular acceleration of the wheel (in rad/s²). Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point. Take g = 9.81 m/s². M Your Answer: Answer G 1
25
A slender, uniform, metal rod with mass M is pivoted without friction about an axis through its midpoint and perpendicular to the rod. A horizontal spring with force constant k is attached to the lower end of the rod, with the other end of the spring attached to a rigid support. If the rod is displaced by a small angle 0 from the vertical and released, show that it moves in angular SHM and calculate the period. (Hint: Assume that the angle 0 is small enough for the approximations sin 0 z 0 and cos 0 z 1 to be valid. The motion is + w?0 = 0, and the period is then T = 21 ) simple harmonic if dt2 d²0 :)
The system is at rest with the spring unstretched when theta = 0. the 5.3 kg uniform slender bar is then given a slight clockwise nudge. The value of b is 0.45 m. (a) if the bar comes to momentary rest when the angle = 58, determine the spring constant k. (b) for the value k = 65 N/m, find the magnitude of the angular velocity of the bar when the angle = 38 degrees. a) k = 70.634 N/m
The radius of the pulley is of inertia is I = 0.1 kg-m2. R = 100 mm The mass stant is k = 135 N/m. m = 5 kg. and its moment The spring conThe system is released from rest with the spring unstretched. What maximum distance does the mass fall before rebounding?
Figure Q2 shows a 100 kg cylinder device has a radius of gyration, m= 400mm. The cylinder device is rolling down to a liner plane distance of 2 m stating from rest. Assume no friction in all contact surface, determine the angular velocity after the releasing. Which energy method is suitable in this application and why? 600 mm 300 mm 45 Figure Q2
7. Consider the system shown below. The spring is connected via a cable to the non-rotating shaft of the roller with mass m₂ and radius R. A second cable connected to the shaft passes through the two pulleys. k ww χ M₁ Use conservation of energy to derive the equations of motion. The equilibrium position corresponds to x = 0. Neglect the masses of the pulleys and assume the cable is inextensivle.
A ball governor of the vertical compression spring type runs at a mean speed of N = 189.228 rev/min. The bell crank lever arms are a = 0.158 m and b = 0.063 m and the rotating balls have a mass of m = 2.793 kg each, and the ball radius is r = 0.114 m at the mean speed. Part A: If the speed range of the governor at the mean speed is A = 1.287 rev/min, determine the friction force Fu at the sleeve (neglect the effect of gravity on the balls). Part B: Determine the spring stiffness S that would be required to make the governor isochronous if the sleeve lift is y = 0.013 m from the mean position (assume the ball arm is vertical at the mean position).
Problem 01 The thin plate ABCD has mass 20 kg and is held in the position shown by a wire BH and the two massless links AF and DE. What is the acceleration of the plate and the forces in each link immediately after the wire is cut? y = 30°. E F 0.3 m A D 0.5 m- H 9 B ↑ 0.25 m C