A 30 cm diameter pipe, conveying water, branches into two pipes of diameters 20 cm and 15 cm respectively. If the average velocity in the 30 cm diameter pipe is 2.5 m/s, find the discharge in this pipe. Also determine the velocity in 15 cm if the average velocity in 20 cm diameter pipe is 2m/s. V2 = 2m/sec D2 = 20cm V, = 2.5m/sec = 30cm %3D V3 = ? D3 = 15cm

A 30 cm diameter pipe, conveying water, branches into two pipes of diameters 20 cm and 15 cm respectively. If the average velocity in the 30 cm diameter pipe is 2.5 m/s, find the discharge in this pipe. Also determine the velocity in 15 cm if the average velocity in 20 cm diameter pipe is 2m/s. V2 = 2m/sec D2 = 20cm V, = 2.5m/sec = 30cm %3D V3 = ? D3 = 15cm

Name: A 30 cm diameter pipe, conveying water, branches into two pipes of di
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: A 30 cm diameter pipe, conveying water, branches into two pipes of diameters20 cm and 15 cm respectively. If the average velocity in the 30 cm diameterpipe is 2.5 m/s, find the discharge in this pipe. Also determine the velocity in15 cm if the avera

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The water is flowing through a pipe having diameters 30 cm and 21 cm at sections land 2 respectively. The rate of flow through pipe is 40 litres/s. The section 1 is 7 m above datum and section 2 is 3 m above datum. If the pressure at section 1 is 37 N/cm? , find the following by neglecting losses: (ENTER ONLY THE VALUES BY REFERRING THE UNIT GIVEN IN BRACKETS) ) Area of cross section of section1 (unit in m?) = Area of cross section of section2 (unit in m?) = velocity at section 1 (unit in m/s) = velocity at section 2 (unit in m/s) = (ii) difference in datum head (Unit in m) = Pressure head at section 1 (Unit in m) = pressure head at section 2 (unit in m) =
Please solve and answer the question correctly. Thank you!!
The following figure shows a bent in a pipe with a diameter of D (cm). Pressure is measured in cross section#1 as demonstrated in the figure as P1 (kPa). In cross section#2 the diameter reduced through a nozzle to 5.0 cm and the water is discharged into atmosphere. The elevation difference between two cross sections is 0.5 m. Assume all losses are negligible and density of the fluid, water, is 1000 kg/m³. a) Find the velocity in cross section#1; b) Calculate the horizontal and vertical forced acting on the pipe and the direction of the resultant force. D = 20 cm, Pj= 450 kPa Cross section#2 0.5 m Diameter: 5 cm P1 60° Cross section#1 Diameter: D cm
A pumping station wet well operates between 540- and 550-ft elevation. The pump curve is deϐined by the following points: 80 ft at zero ϐlow, 78 ft at 200 gpm, 65 ft at 800 gpm, and 50 ft at 1200 gpm. The pump discharge contains an equivalent of 50 ft of 6-in. pipe. The discharge pipe is 120-ft long and terminates at a splitter box, elevation 570. Using C=100, plot the pump curve and the corrected pump curve. Plot the pump discharge curves at each wet well elevation and for C=100 and C=140. What is the pump ϐlow at the low and high wet well elevations for newand old pipe?
Please solve it quickly I am at the exam
Consider the mechanical energy equation: P + VB? + gzB =PA + V? + g ZA + w – loss A +g ZA + W – loss where loss 2 0 Select ALL true statements below. a fluid particle will flow through point A before point B a fluid particle will flow through point B before point A points A and B do not lie on the same streamline if a turbine is present, w < 0 if a pump is present, w < 0 if the fluid is perfectly inviscid, loss can be 0
Complete Solution please, thanks. 3. A vertical circular stack 30 m high converges uniformly from a diameter of 6 m at the bottom and 4.5 m at the top. Gas with a unit weight of 0.12 N per cubic meter enters the bottom of the tank with a uniform velocity of-assume values with decimals between 3 to 4 m per second- enters the stack. The unit weight increases by 7.5 percent every 2 meters. Find the velocity of flow at every 5 meters along the stack.
Water is pumped into a fire hose through a 6 cm diameter pipe with speed 1m/s. The water in the fire hose flows with a pressure of 200000 Pa. At the end of the fire hose is a nozzle (small hole). The pressure decreases to atmospheric pressure (101300 Pa) when the water leaves the nozzle from the hose. There is no change in height moving from the hose to the nozzle. 1. What is the water speed in a 4 cm diameter fire hose? 2. What is the velocity of the water exiting the nozzle (p=1000kg/m³)? 4. What is the diameter of the nozzle? 3. A Fireworker now connects an additional flexible tube to the nozzle (tube and nozzle has same diameter). He lifts the tube to a height of 1 meter above the ground. At what speed does the water come out of the tube? (hint - the pressure at the exit is still atmospheric)
asap pls
Fluid flows through the pipe out of a rigid tank in the shape of a cube. During that process, heat is transferred into the rigid tank. Show the correct final form of energy equation valve m_cv2*u_cv2-m_cv1*u_cv1=-m_out*h_out+Q_in m_cv2*u_cv2-m_cv1*u_cv1=-m_out*h_out+Q_in+W_in m_cv2*u_cv2-m_cv1*u_cv1=m_in*h_in+Q_in-W_out m_cv2*u_cv2-m_cv1*u_cv1=-m_out*h_out-Q_out O m_cv2*u_cv2-m_cv1*u_cv1=m_in*h_in+Q_in
2. For storimg purposes, water is to be moved from one pool to another that is 50 ft above the first one using a pump and an 8-in. inside-diameter pipe. The flow rate of the water is 2.5 ft’/s. There is a loss of available energy as 61 V²/2ft?/s² where Vis the average velocity of water inside the pipe. Determine the amount of shaft power required, in hp.
a) Develop an equation for the head (in ft) developed by the pump described by the chartas a function of flow rate (in gpm) when the pump uses a 9 ¾” impeller. b) Develop an equation for the pump efficiency as a function of flow rate (gpm) when the pump uses a 9 ¾” impeller.