A 3-phase 11kv generator feeds power to upf load of 100mw through 3-phase transmission line. The line to line voltage is maintained constant at 11kv. The impedance of line based on 100mva and 11kv is j0.2pu. The line to line voltage at terminal is 11kv. Determine the total reactive power injected at the terminal of load to maintain the line voltage at 11kv.

A 3-phase 11kv generator feeds power to upf load of 100mw through 3-phase transmission line. The line to line voltage is maintained constant at 11kv. The impedance of line based on 100mva and 11kv is j0.2pu. The line to line voltage at terminal is 11kv. Determine the total reactive power injected at the terminal of load to maintain the line voltage at 11kv.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For a power station the yearly load duration curve is a straight line from 50,000 to 4000 kw. To meet the load three turbo-generators are installed. The capacity of two generators is 16,000 kw each and the 3rd is rated at 7,000 kw. Determine the following a) Load factor. b) Capacity factor. c) Maximum demand.
The shown distribution network is to supply two factories A & B with load curves indicated. Assume that both factories have a lagging power factor of 0.8 . a) Select the required sizes of transformers for both factories such that in the case of a failure in one transformer the overload on the remaining ones should not exceed 15% . b) Select the required sizes of fuses to be installed at both sides of transformers. c) Calculate the annual energy losses in transformers of factory A. Assuming that transformers are in operation continuously . d) Select the required size of the 11KV. XLPE cables for the distribution network , if cables are to be laid direct in ground with тахітит ground temperature of 30° С. e) Calculate the annual energy losses in cables of section SA . S 2 Km A 3 Km 11/0.4 KV Trans. 11/0.4 KV Trans. Factory A PF = 0.8 lag. Factory B PF = 0.8 lag. | S (KVA) 500 |S (KVA) 500 400 400 300 300 200 200 100 100 Time (hr) 24 Time (hr) 24 6. 12 18 12 18 Load curve of Factory (A)…
For all of the Questions use 4 most significant digits after the decimal point (e.g.: ) 1. A three-phase load draws 720 kW from the grid with 0.8 lagging power factor. The load is balanced and star connected. For reactive power compensation, a bank of capacitors is connected in star across the load terminals. With this compensation, active power loss across the lines is reduced 10% (Meaning that If the power loss is 1 unit before compensation, power loss is 0.9 unit after compensation). Assuming that compensation does not change the load terminal voltage, calculate a) b) c) The kVAr rating of capacitors in each phase The improved power factor The new power factor if the same bank of capacitors is connected in delta Hint: The power loss across the line is proportional to the line current and hence the apparent power.
2. a) Explain the terms load factor and diversity factor. b) Discuss the advantages of interconnected grid system. c) A generating station is to supply four regions of load whose peak loads are 10 MW, 5 MW, 8 MW and 7 MW. The diversity factor at the station is 1-5 and the average annual load factor is 60%. Calculate: (i) the maximum demand on the station, (ii) annual energy supplied by the station and (iii) suggest the installed capacity and the number of units.
Solve it quickly please
In an installation there is a three-phase load of 300 kVA with a power factor of 0.8 behind, in parallel with a three-phase load of 150 kVA with a power factor of 0.6 ahead. A pure reactive element is connected in parallel, and a unity power factor is obtained at the power input. Indicate the reactant of the element, with a positive sign if it is a bank of reactors, or with a negative sign if it is a bank of capacitors. Just put the corresponding sign followed by the numerical value, without units. The numerical value must correspond to the three-phase kVARS. You can use integer values with no decimal places or up to two decimal places
4. A 4160V, three phase source, 4-wire supplying an unbalanced three phase load. The unbalanced connected load are: Zan = 150/53.13° ; Zbn = 150-53.13° ; Zen = 1500° Assuming positive sequence and the reference is the line voltage "a", determine: a. the line current "a" b. the line current “b” c. the line current "c". d. the total real power e. the total reactive power f. the total apparent power g. the overall power factor. h. the neutral current.
In a given system of base power of 250 MW, and bus 3 is taken as reference. The per-unit reactances are X₁2 = 0.2 p.u., X13 = X23 = 0.1 p.u. If the power flow in the system is given as: PF12 = 100 MW, PF13 = 50 MW, PF23 = -150 MW, then the phase angles are Select one: O a. 0₁ = 0.02 rad., 0₂ = 0.06 rad., 03 = 0 rad. O b. None of these O c. 8₁ = 0.02 rad., 02 = -0.06 rad., 03= 0.1 rad. O d. 0₁ = 0.02 rad., 02 = -0.06 rad., 03 = 0.2 rad. O e. 8₁ = 0.02 rad., 8₂ = -0.06 rad., 03 = 0.1 rad. O f. 0₁ = 0.02 rad., 02 = -0.06 rad., 03 = 0 rad.
The figure below shows the one-line diagram of a four- bus power system. The voltages, the scheduled real power and reactive powers, and the reactances of transmission lines are marked at this one line diagram (The voltages and reactances are in PU referred to 100 MW base. The active power P2 in MW is the last three digits (from right) of your registration number (i.e for the student that has a registration number 202112396, P2 =396). [10] Starting from an estimated voltage at bus 2, bus 3, and bus 4 equals V2 (0) = 1.15<0°, V3 = 1.15 < 0°, V4 1.1< 0°. 1- Specify the type of each bus and known & unknown quantities at each bus. 2- Find the elements of the second row of the admittance matrix (i.e. [Y21 Y22 Y23 Y24]). 3- Using Gauss-Siedal fınd the voltage at bus 2 after the first iteration. 4- Using Newton-Raphson, calculate: |- The value of real power (P2), at bus 2 after the first iteration. Il- The second element in the first row of the Jacobian matrix after the first iteration. 2 P2…
Kindly solve it
A system consists of four idenital 400 MVA generating units feed- ing a total load of 1016 MW. The intertia constant of each unit is 5 on 400 MVA base. The load changes by 1.5% for a 1% change in frequency. When there is sudden drop in load by 16 MW, obtain the power system time constant (T) with constants H and D expressed on 1600 MVA base.
Two parallel loads are connected to a 120 volt rms, 60 Hz power line. One load absorbs 10 k watts at 0.8 power factor lagging. The second load absorbs 4 k watts at 0.9 power factor leading. Determine the real (watts) and reactive (VARS) power of the combined load.