A 3-ph transmission line has a total length of 200 km. This transmission line has a resistance of 0.16 Ohm per phase per km, an inductive reactance of 0.25 Ohm per phase per km, and a shunt admittance of 1.6 micro Siemens per phase per km. When this transmission line is supplying a load with 20 MW at (V) kV and 0.8 lagging power factor where V = 100 +24 Using long length representation, find: 1- The voltage drop across this T.L. Suggest verifying your suggestion a way to decrease|this voltage drop to 50%. 2- The transmission line efficiency. 3- The loadability of transmission line (approximate calculations). Suggest verifying your suggestion a way to increase this loadability to three times. 4- The propagation velocity and the corresponding wave length.

A 3-ph transmission line has a total length of 200 km. This transmission line has a resistance of 0.16 Ohm per phase per km, an inductive reactance of 0.25 Ohm per phase per km, and a shunt admittance of 1.6 micro Siemens per phase per km. When this transmission line is supplying a load with 20 MW at (V) kV and 0.8 lagging power factor where V = 100 +24 Using long length representation, find: 1- The voltage drop across this T.L. Suggest verifying your suggestion a way to decrease|this voltage drop to 50%. 2- The transmission line efficiency. 3- The loadability of transmission line (approximate calculations). Suggest verifying your suggestion a way to increase this loadability to three times. 4- The propagation velocity and the corresponding wave length.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Which one of the following is the definition of slurry? a. Water only b. Animal waste (Dung) only c. The mixer of Water and Bio gas d. The mixer of Water and Animal dung
A galvanometer is used as a _________a) current sourceb) voltage sourcec) null detectord) input impedance
For minimizing the bit error probability, the value of the argument in the Q-error function should be ------- a. equal to zero b. equal to 1 c. decreased d. increased This multiple choice question from DIGITAL COMMUNICATIONS course.just write for me the final answer.
What do these words means? Use it can..or it can't.. If something is Washable, - Unbreakable, it-- Edible,--- , Unusable,--
Briefly discuss the loaded and non-loaded telephone cables
List six things to Cheak as part of routine preventive maintenance for large contactor
UP/DOWN CLK Qo Q₁ Q₂ Q4 (UP) (DOWN) _____ (UP) (DOWN) 山 In
Enumerate 5 or more home safety tips to avoid short circuits.
Question 10A-How is the minimum number of receptacle outlets determined for theliving room? What article of NEC is talking about this? B-What must be installed wherever outlets are required according to theNEC? What article of NEC is talking about this requirement?C-Which part of the NEC standard proposes the switches requirements? D-If the branch circuits supplying the receptacles in the figure at 15 A,what's the minimum size of the conductors in the branch circuit? E-According to the AEC standard, how many outlets can a GFCI protect?
1 degree of closeness to the true value. It is often expressed as a percentage full scale deflection is called ______________ a. Sensitivity b. Error c. Accuracy d. Range
conduits are most suitable for house flats and offices.
Arduino - (b) The Arduino IDE provides a serial monitor for soft debugging purposes. Demonstrate how this can be accomplished by writing a simple program to perform the following task continuously on an Arduino UNO: Read a digital input from an external push button and print the state of the button as "Pressed" or "Not Pressed" to the serial monitor. The push button is connected to digital pin 5, and is configured as active low. Apply the proper Arduino C setup and loop structure, and present suitable comments with each line of your program.