A 3-m-internal-diameter spherical tank made of 1-cm-thick stainless steel is used to store iced water at 0°C. The tank is locater putdoors at 25°C. Assuming the entire steel tank to be at 0°C and thus the thermal resistance of the tank to be negligible, determine (a) the rate of heat transfer to the iced water in the tank and (b) the amount of ice at 0°C that melts during a 24- hour period. The heat of fusion of water at atmospheric pressure is h = 333.7 kJ/kg. The emissivity of the outer surface of the cank is 0.75, and the convection heat transfer coefficient on the outer surface can be taken to be 30 W/m2 - °C. Assume the average surrounding surface temperature for radiation exchange to be 15°C.

A 3-m-internal-diameter spherical tank made of 1-cm-thick stainless steel is used to store iced water at 0°C. The tank is locater putdoors at 25°C. Assuming the entire steel tank to be at 0°C and thus the thermal resistance of the tank to be negligible, determine (a) the rate of heat transfer to the iced water in the tank and (b) the amount of ice at 0°C that melts during a 24- hour period. The heat of fusion of water at atmospheric pressure is h = 333.7 kJ/kg. The emissivity of the outer surface of the cank is 0.75, and the convection heat transfer coefficient on the outer surface can be taken to be 30 W/m2 - °C. Assume the average surrounding surface temperature for radiation exchange to be 15°C.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider a furnace (as a plane wall) which has a thickness of 15 cm and a surface area of 1 m?. The inside surface of the furnace wall (the hot left side of the wall) is at temperature T1. The furnace wall is made of brick with thermal conductivity of 1.198 W/m.K. The outside surface of the furnace wall (the right side of the wall) has a surface emissivity of 0.8 and is maintained at T2=101 °C and subject to air at 25 °C with convection heat transfer coefficient of 20 W/m?.K. The surroundings temperature at the outside of the furnace wall is at 25 °C. Required: Draw a clear and consistent schematic of the problem and label the operating conditions on the schematic. Perform systematic analysis, state your assumptions and justify the equation used and determine the following (circle your final answers): (i) The rate of heat transfer by convection (in W); (ii) The rate of heat radiation (in W); (iii) The surface temperature of the furnace wall T1 (in °C); (iv) The rate of conduction heat…
water 4-26 Steel rods (p = 7832 kg/m³, c, = 434 J/kg-K, and k = 63.9 W/m-K) are heated in a furnace to 850°C and then quenched in a bath at 50°C for a period of 40 s as part of a hardening process. The convection heat transfer coefficient is 650 W/m²K. If the steel rods have diameter of 40 mm and length of 2 m, determine their average temperature when they are taken out of the water bath.
An ice chest whose outer dimensions are 30 cm*40 cm*40 cm is made of 3 cm thick Styrofoam (k = 0.033 W/m°C). Initially, the chest is filled with 30 kg of ice at 0 °C, and the inner surface temperature of the ice chest can be taken to be 0 °C at all times. The heat of fusion of water at 0 °C is 333.7 kJ/kg, and the surrounding ambient air is at 20 °C. Disregarding any heat transfer from the 40 cm*40 cm base of the ice chest, determine how long it will take for the ice in the chest to melt completely if the ice chest is subjected to (a) calm air and (b) winds at 30 km/h (assume the heat transfer coefficient on the front, back and top surfaces to be the same as that on the side surfaces). Use the thermophysical properties of air as follows: k = 25.5×10-3 W/mK, ν = 15×10-6 m2/s, α = 21.1×10-6 m2/s, and β = 3.43×10-3 K-1.
Thin walled Aluminum container that is 6 cm in diameter and 7 cm in high equipped with stirrer contain water submersed in hot engine oil at 60°C. If the oil was mixed by the stirrer and the heat transfer coefficient between the water and the glass is 120 W/m2. °C. Find the time needed for the water to heat up from 3°C to 38°C
based on a large 4 cm thick plate that is initially at a uniform temperature of 20°C that is heated by passing it through a space maintained at 500°C. The plate remains in the space for a period of 7 min. Take the heat transfer coefficient to be 120-W/m2°C. Example 4-4 [k = 110-W/m°C, r = 8530-kg/m³, C, = 0.380-kJ/kg°C, a = 33.9 x 10-6 m²/s] The dimensionless distance from center to a point 0.4-cm below the outer surface is 0.5 0.8 none of the above 0.2
A house has a three meter deep basement (foundation) wall that is in a 10 meter by eight meter rectangular shape based on interior dimensions. On average, 2.5 meters of the wall is below grade. Assume the outside air temperature is 38°C and the inside temperature is 20°C; there is an average ground temperature of 27°C. Determine the rate of heat loss through the wall if it is insulated with an R-value of about 30°C.m^2/W.
A 0.5-ampere current is flowing through a long electrically conducting cylindrical rod. The diameter of the rod is 6 mm, the electrical resistance of the rod is R = 2000 /m, and k =0.9 W/m K for the rod. The rod is encased in a 2-mm thick Pyrex tube and a 20°C liquid is flowing over the outer surface of the Pyrex tube. The convection heat transfer coefficient for the liquid h= 800 W/m2 . K. The interfacial conductance (contact resistance) at the interface between the rod and the Pyrex tube is h = 1200 W/m² - K. a) Compute the rate of heat generation in the rod and use it compute the volumetric rate of heat generation. b) Find the temperature drop across the interface between the outer surface of the rod and the inner surface of the Pyrex tube. c) Find the temperature at the center of the rod.
A pipe in a manufacturing plant is transporting superheated vapor at a mass flow rate of 0.3 kg/s. The pipe is 10 m long, has an inner diameter of 5 cm and pipe wall thickness of 6 mm. The pipe has a thermal conductivity of 17 W/m.K, and the inner pipe surface is at a uniform temperature of 120 °C. The temperature drop between the inlet and the exit of the pipe is 7 °C, and the constant pressure specific heat of vapor is 2190 J/kg.°C. If the air temperature in the manufacturing plant is 25°C, determine the heat transfer coefficient as a result if convection between the outer pipe surface and the surrounding air. T(r) = 120°C Superheated Air, 25°C r2 vapor r1 0.3 kg/s L = 10 m Tin-Tout = 7°C
An electric device made of copper stands on an insulating carpet in a breezy room at 20°C. A fan is set in the room to ensure a continuous air circulation. Determine the total rate of heat transfer from the device if the average values of its exposed surface area and outer surface temperature are 2.5 m² and 30°C, respectively.