A 3 m high, 6 m wide rectangular gate is hinged at the top edge at A andis restrained by a fixed ridge at B. Determine, the hydrostafic force e xertedon the gate by the 5 m high water and the locafion ofthepressure center:2mwaterGate3m

Hydrostatic force: The fluid exerts pressure on any type of body with vertical, horizontal, and…

A 3 m high,6 m wide rect an gular gate is hinged at the top edge at A and is restraine d by a fixed ridge at B.Determine. the hydrostatic force exerted on the gate by the 5m high water and the locafion of the pressure center: 2m water Gate 3m

A 3 m high,6 m wide rect an gular gate is hinged at the top edge at A and is restraine d by a fixed ridge at B.Determine. the hydrostatic force exerted on the gate by the 5m high water and the locafion of the pressure center: 2m water Gate 3m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Problem 4. The gate below is 1.5 m wide and hinged at point B. It rests against a smooth wall at…

Q: Find the hydrostatics forces on the 4m diameter gate if the gauge pressure reading is of 83KP.. 30°…

Q: A rectangular altitude of 2.4 m. The short side of the gate is flushed with the water surface.…

Q: Problem 3 A 5-m long and 2-m wide gate contains water with a depth of 4 m as shown and is supported…

Q: 1.0 A RECTANGULAR GATE 2.0 M X 5.0 M IS ACTED ON WATER ON ONE SIDE AND IS POSITIONED WITH ITS LONGER…

Q: 6 m/s ter flows through the e at A at 6 m/s. termine the pressure A and the velocity of 3 m water as…

Q: a. Determine the horizontal component, vertical component, and the resultant of the hydrostatic…

Q: Determine the resultant force and the location of the centre of pressure due to the water pressure…

Q: As shown in Fig. determine the submerged depth of concrete cylinder (h), for equilibrium the gate…

Q: *6-4. Water flows with a velocity of 6 m/s through the pipe at A. If the pressure at A is 65 kPa,…

Q: 7. Gate AB as shown if figure is 2m high and 3 m wide. It supports water on the left side at the…

Q: -4 m wind 12 m -4 m 17 11 11 11 2 m B 3 m 3 m 3 m 3 m

Q: 24 kN S KN/m D 3m- 3m→-3m

Q: A 1.5m semi cicular gate is submerged in oil having an SG of 0.95. its base is 2m from the surface…

A: Given data- Diameter of semi cicular gate (d) = 1.5m Specific gravity of oil(S.G) = 0.95 Density…

Q: A rectangular gate 1.2 m by 3 m is inclined 60° with the horizontal. The top of the gate is…

Q: Draw the S.F.D and B.M.D for the girder in the system shown in Fig. (5).. 230 2m 60 kN/m 4 m 2 m →

A: The girder system is given, we need to draw Shear force and bending moment diagram

Q: A gate 3m high is 1.5m wide is hinged at point B and rest against a smooth wall at A. Point A 1.8m…

Q: hinge 1.2m water 2.4m В 1.8m N A rectangular gate AB shown is hinged at "A" and rests on a smooth…

Q: 4. A long, continuous steel gate, BC, restrains fresh water as shown and is supported by hinges at…

A: Given : Determine the reaction component for a typical hinge at A and at B ?

Q: 2. Find and draw influence lines of Fed, and the vertical component of Fec. A B D E F 5 m d 6 at 6 m…

Q: The weight and diameter of the block are 56,12 kN and 1 m, respectively. Determine the height of H…

Q: 4-33. The pipe assembly is subjected to the force of F = {6001 + 800J – 500k} N. Determine the…

Q: Problem 4. The gate below is 1.5 m wide and hinged at point B. It rests against a smooth wall at…

A: Width of gate = 1.5 m Hinged at point B Specific gravity of sea water = 1.025 To find:- Force on…

Q: 2. Analyze the bem below supfart B Settes =4mut Suppert D setth =2mm 80 kN 20 kN/m A

A: Given data:- δB = 4 mmδD = 2 mmE = 200 GPa = 200×106 kN/m2I = 800×10-6 m4

Q: Question 3 (c) Using the same problem above. Where will single support be located to hold the gate…

A: As per question, I solved here only Part (C). This question is related to the Fluid Mechanics from…

Q: 3. What is the difference in the position of the pressure center (h.) for the gate if it is…

Question

100%

A 3 m high, 6 m wide rectangular gate is hinged at the top edge at A and
is restrained by a fixed ridge at B. Determine, the hydrostafic force e xerted
on the gate by the 5 m high water and the locafion of
the
pressure center:
2m
water
Gate
3m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Introduction

VIEW

Calculation

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Problem 2 Water flows through a horizontal 45 degree bend with a 22-in dimeter at a rate of 20 ft³/s under a pressure of 15 lb/in². a. In the x-direction P₁ b. In the y-direction y κα F *P2, Fx F Neglecting the head loss in the bend, calculate the resisting force required to anchor this pipe bed: X
A vertical gate 1.50 m wide and 2.0 m high has water on one side and is inclined 45° with the horizontal. Water is 1.60 m above the top of the gate where the hinge support is located. Compute the location of the center of pressure from the bottom. (Multiple choice a. 0.383m b.0.883 m c. 0.338 m d. 0.838 m)
3) Gate AB is 3.20 m long. Find the horizontal force H to hold the gate in equilibrium. (Width of AB is 2.0m). 60 cm Oil (8 0.80) Water 60° H
Determine the force F that necessary to keep the gate ACB (2 m wide) at its position. F A Water Oil, SG = 1.5 Parapolic 4 m 3 m х Di Hinge { / Y 9 m
Gale AB is 8m wide. (a.) Compute the vertical component of the total hydrostatic force acting on gate AB. (b.) Compute the tolal reaction acting in the hinge at B. I 7-5 m 12 m Water Parabols
Problem 4. The gate below is 1.5 m wide and hinged at point B. It rests against a smooth wall at point A. Compute (a) the force on the gate due to the pressure of the seawater (specific gravity is 1.025 at 25°C), (b) the horizontal force, P, exerted by the wall at point A, and (c) the reaction at hinge, B. 4.5 m Р atmos Sea- water Gate ↑ 1.8 m B 2.4m P
ASAP dont round in initial values, only round off in final ans plzs
Refer to the composite body shown. Given: P1=14.7kN, P2=16.9 kN Solve for the reactions at pin support at A and roller support at B and determine the internal reactions at each connection- B,C,D.
The rectangular (0.6mx0.9m) sluice AB blocks liquid with a specific gravity of 0.79. The sluice door weighs 300N and finds the force that must act on the cable BCD to open the sluice door.