A 25cm circular pipe carries 0.16m3 /sec of water under a pressure of 200Pa. The pipe is laid at an elevation of 10.71m above the mean sea level (MSL) of Ibadan. What is the energy head measured with respect to the MSL? If = 9810N/m3 (9.81KN/m3).

Q: At a point in a 15 cm diameter pipe, 2.5m above its discharge end, the pressure is 250 kPa, If the…

A:

Q: A reservoir like the one shown has SAE10 oil at 20 C and is connected to a capillary tube for…

A: Neglect major and minor losses

Q: A 9.8 m A fluid of relative density 0.88 is flowing through a pipe constant diameter of 15 mm (see…

A: Fluid relative density = 0.88 PA = 150 KPa PB = 225 KPa ZA = 9.8 m ZB = 0 m

Q: The difference of mercury level in a differential U-tube manometer connected to the two tapping of…

A:

Q: stants, calculate the time required for the discharge through the orit D. The initial level…

A:

Q: Q2: What would be the discharge of liquid (u = 1.48x 10-6 m2/sec, s = 0.89) through a smooth pipe of…

A:

Q: Water at 68°F flows uphill (B to A) in a 4 inch inside diameter cast iron pipe at a rate of 1.5…

A:

Q: p1: oil with viscosity (2n10 N.s/) and densily af (850 kg) is Pumped along astraight herizon hal…

A: Given, Density of oil, ρ=850kg/m3Viscosity of oil, μ=2×10-2 (Ns/m2)Discharge,…

Q: Benzene (p = 881 kg , u = 6.51 x 10-4 9) flows through a galvanized iron horizontal 5 m long pipe of…

A:

Q: Pressure loss along a pipe pumping water is 6.6Pa. If the pipe is 2.1m long, what angle (in degrees)…

A: To overcome the pressure drop along the pipe, we need to consider the effect of gravity on the water…

Q: [Mechanical] A 10cmm diameter external cylindrical mouth peice discharge under head of 4m .determine…

A:

Q: Calculate the dynamic force of the water on the fork, referring to a horizontal plane

A:

Q: Consider the following pipe system. The three water-filled tanks are connected by pipes with…

A: Given dataD1=0.10mν=1×10-6m2/sQ=0.028cms

Q: Water flows in a pipe at 0.015 m³/s. The pipe is 50 mm bore diameter. The pressure drop is 13 420 Pa…

A:

Q: A venturi meter with a 1.0 in. diameter throat is mounted in a 2.0 in. diameter pipe carrying water…

A: Solution: Given Data: D=2 ind=1 inρ=63.36 lbm/ft3μ=7.536×10-4 lbm/ft-sSG=13.55∆P=5 in HgCD=0.98

Q: i just need final answer The water is delivered with piping system given in the figure below. The…

A:

Q: A mercury manometer installed across an orifice meter (diameter = 1.2 cm) in a horizontal pipe…

A: Given: d = 1.2 cm = 0.012 mD = 2.35 cm = 0.0235 mh = 12 cm = 0.12 m Taking the density of mercury as…

Q: A Horizontal tube has a diameter of 7 in., in which alcohol (spec. grav. = 0.80) is flowing at the…

A:

Q: I need complete solution (step by step process) with given. Thanks Note: Instead of using g = 9.81…

A: Hl=1.39 mL=40 mf=0.012Q=600 L/s =0.6 m3/sg=9.806 m/s2

Q: Oil flows in a pipe 80 mm bore diameter with a mean velocity of 0.4 m/s. The density is 890 kg/m3…

A:

Q: A paint shop in the water flow through the pipe in the radius rQ=0.05 m/s, density p = 1000 kg/ m…

A:

Q: Q8)A duct of 65 cm diameter and 15m long carries 120 m³/min of air. Find the pressure loss in the…

A:

Q: 3. Compute the friction head loss in meters of a fluid at a certain condition (S.G.-1.101) that is…

A:

Q: Problem 2 The 10 cm galvanized-steel pipe is 1000 m long and discharges water into the atmosphere.…

A:

Q: A smooth pipe carries water at the rate of 300 L/s, kinematic viscosity is 10 m/s , with a head loss…

A: Given, Q = 300 L/s = 0.3 m3/s Kinematic viscosity = v = 10-6 m2/s Head loss = hf = 3 m Length of…

Q: Two reservoirs are connected by 198ft of 2-in diameter tubing. What is the flow rate when the…

A: The calculated flow rate in ft3/s.

Q: A pipe of diameter 18 cm, is used to pump the water to the house in the Hamra hill at the height of…

A: Write the given values along with the suitable variables.

Q: A (300mm) diameter of pipe, if the discharge (90 L/sec), nozzle diameter (75mm) and pipe length from…

A:

Q: Calculate the available net positive section head NPSH in a pumping system if the liquid density p…

A:

Q: The total head of fan is 200m and has a static pressure of 201mm of water gage. What is the velocity…

A:

Q: A flow nozzle with a throat diameter d of 6-inches is being used to measure the flow rate of hot…

A: Given Data: d=8 inT=80oF12 inch SCH 80 pipe∆P=1.46 psiC=0.96   To Find: The flow rate of water in…

Q: hsllo

A: Given: The specific gravity of petrol is, ρp=0.81. The specific gravity of oil is, ρm=13.6. The…

Q: If L =4.5 km, d- 40 mm and Az 100 m, what will be the flow rate of water in m'/hr. Make suitable…

A: