A 250 mm x 125 mm venturimeter is provided in a vertical pipe line carrying oil of specific gravity of 0.9, the flow being upwards. The difference in elevation of the throat section and entrance section of the venturimeter is 0.5 m. The differential U-tube mercury manometer shows a gauge deflection of 300 mm. Coefficient of venturimeter is 0.96 and specific gravity of mercury is 13.6 Calculate the following: a) Discharge of oil b) The pressure difference between the entrance section and the throat section..

A 250 mm x 125 mm venturimeter is provided in a vertical pipe line carrying oil of specific gravity of 0.9, the flow being upwards. The difference in elevation of the throat section and entrance section of the venturimeter is 0.5 m. The differential U-tube mercury manometer shows a gauge deflection of 300 mm. Coefficient of venturimeter is 0.96 and specific gravity of mercury is 13.6 Calculate the following: a) Discharge of oil b) The pressure difference between the entrance section and the throat section..

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Please use the second photo as a format of solution. Please write properly. THANKS!
Compute the pressure @ point n ( Pn ) as shown by the differential manometer in KPa if pressure @ point m ( Pm ) is equal 1027.66 mm Hg. air plpeline where: a= 12" b=3,2 C-4.0 d- 12 m mercury density (16 300 kghm) water pipeline
Problem : Find the difference in manometer reading for the pipe shown below. The diameter of the pipe is 10 cm, and the flow rate is 0.01 m³/s. The roughness height (ɛ) of the pipe material is 0.15 mm. The kinematic viscosity of water is 1.0x10-6 m²/s. Ah = ? 30 m Water
A plate 0.05mm distant from a fixed plate moves at 1.2m/sec and requires a fore of 2.2 N/m² to maintain this speed. Find the viscosity of the fluid between theplates. 1& Dr. Ahmed Raho
A Pipe carrying oil of specific gravity 0.92 changes in size from 250 mm at section 1 and 550 mm at section 2. Section 1 is 4.2 m below section 3 and the pressures are 90 kPa and 60 kPa respectively. If the discharge is 150 lit/sec, determine the head lost and the direction of flow. provide complete solution asap.
. In a V-notch, an'error of 1% in the measurement of head would constitute in the discharge measurement, an error of:
A venturi meter of 150 x 75 mm size is fixed in a horizontal pipe carrying water. The pressure gauge at entry read 137.34 kN/m^2 (gauge). The pressure at the throat was 37.5cm of mercury (vacuum). STRICTLY SHOW THE COMPLETE FBD OF THE PROBLEM
PROBLEM 2 The pipe bend shown is in a horizontal plane. Oil with a specific gravity of 0.86 enters the reducing bend at section A with a velocity of 3.2 m/s and a pressure of 150 kPa. Neglecting head loss, determine (a) The velocity at section B, V (m/s) (b) The pressure at section B, ps (kPa) (с) Fмх (N) (d) FMY (N) (е) Fpx (N) (f) Fpy (N) (g) The x-component of the reaction by the bend, FRx (N) and (h) The y-component of the reaction by the bend FRY (N). de = 100 mm B- da = 150 mm 30°
Heavy oil discharges from a pipe through a sharp-crested, 100-mm-diameter orifice having discharge coefficient of 0.63. (a) What is the coefficient of velocity? (b) What is the velocity (m/s) of oil jet? (c) What is the head loss (m) through the orifice? 250 Orifice 1 Pipe OIL (SG = 0.91) MERCURY (SG = 13.6) NOTE: easurements are in 'mm' 350
18
Question 3: 150 m long commercial steel pipe is to convey 30 L/s of oil (s=0.9, μ-0.038 N.s/m² from one tank to another (submerged discharge) where the difference in elevation of the free liquid surface is 2 m. The pipe entrance is flush and there is a fully open gate valve in the line. Using only basic scientific calculator, find the diameter theoretically required. Use k=0.19 for fully open pipe or follow the following table (Table 8.3). Flush Valve L, e, Q TABLE 8.3 Values of loss factors for pipe fittings Fitting k 10 Globe valve, wide open Angle valve, wide open Close-return bend 5 2.2 L/D 350 175 75 T Az
Complete answer for upvote else dislike,.