A 25 mm thick high tensile steel tyre is shrunk on a cast iron rim of 500 mm internal diameter and 600 mm external diameter. On shrink fitting the tyre exerts a pressure of 5 N/mm2 on the rim. Determine the inside diameter of the tyre (by taking into account the radial interference). Take: for steel E = 210 GPa and Poisson's ratio v = 0.3. For cast iron E 100 GPa and v=0.25. %3D

A 25 mm thick high tensile steel tyre is shrunk on a cast iron rim of 500 mm internal diameter and 600 mm external diameter. On shrink fitting the tyre exerts a pressure of 5 N/mm2 on the rim. Determine the inside diameter of the tyre (by taking into account the radial interference). Take: for steel E = 210 GPa and Poisson's ratio v = 0.3. For cast iron E 100 GPa and v=0.25. %3D

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.73P: The normal pressure acting on the disk of the sander is given by p=(4/3)+(r2/6), where p is the...

See similar textbooks

Similar questions

It is required to design a square key for fixing a pulley on the shaft, which is 50 mm in diameter. The pulley transmits 10 kW power at 200 rpm to the shaft. The key is made of steel 45C8 (o, = 380 N/mm²) and the factor of safety is 3. Determine the dimensions of the key.
find the displacements at the inner radius of a long cylinder of inside diameter 80mm and outside diameter 120mm snugly fits in a hole over its full length. The cylinder is then subjected to an internal pressure of 2MPA. Using two elements on the 10mm length.
I need the answer as soon as possible
The axial pressure on a single disc clutch (both sides of the disc is effective) is limited to 0.12 Mpa. This is designed for a vehicle with 13kW power at a speed of 700 rpm. Assume uniform wear conditions and a friction coefficient of 0.25. If the outer dimater of the disc is 1.25 times the internal diameter, determine the dimensions of the disc lining and the axial force exerted by the springs.
Q2: A rectangular key is used to connect a gear on a shaft of d=50 mm. The shaft transmitting power at a maximum shear stress. The shaft is made of AISI 1040 CD steel and the key is made of AISI 1020 CD steel. Design the dimensions of the key. Take F.S =3.
Design the rectangular key for a shaft of 50mm diameter. The shearing and crushing stresses for the key material are 42MPa and 70MPa. Determine the length in mm. From Table 13.1, we find that for a shaft of 50mm diameter, the Width of the key. w=16mm and thickness of the key, t=10mm
An 8 in-diameter air compressor is operating with a maximum pressure of 10 psi. The bolts have a yield stress of 6,400 psi. Which of the following is the stress area in sq. in. of the bolt? (Hint: Solve for the applied load first using the given pressure) Group of answer choices 0.61 0.59 0.55 0.57
The two square-jaw grips have the dimensions shown in the figure and are made of mild steel. The clutch is designed to transmit a power of 1.8 kW at 600 rpm. Calculate the surface pressure and shear stresses on the wedges and jaws. they all in mm
he wheel is subjected to a torque of M=55 N-m. The oefficient of kinetic friction between the band brake and the rim of the wheel is =0.3. (Figure 1) Figure 1 W of 1 150 mm M C Part A Determine the smallest horizontal force P that must be applied to the lever to stop the wheel Express your answer to three significant figures and include the appropriate units. P- μA Value Units Submit My Answers Give Up DELL ?
i need the answer quickly
In Fig. 6-38 the maximum lining pressure for any point on the brake is to be limited to 100 psi; μ = 0.2. Find the torque capacity of the brake and the value of force P. Ans. T = 9,080 in-lb, P = 487 lb
Pr