A 235V, 50HZ, single phase motor takes current of 6A at a PF of 0.5 lagging. Determine the value of capacitor required to improve the PF to 0.91. Active component of the current, OP= Reactive component of the current, PR= I(new) taken by the motor with capacitor connected, OQ= Active component of the current (with capacitor), PQ=

A 235V, 50HZ, single phase motor takes current of 6A at a PF of 0.5 lagging. Determine the value of capacitor required to improve the PF to 0.91. Active component of the current, OP= Reactive component of the current, PR= I(new) taken by the motor with capacitor connected, OQ= Active component of the current (with capacitor), PQ=

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Explain how to solve gates in plane questions with laws
gn In/Sign Up OSign In/Sign Up 006157 Exam + >C合 assignments.pennfoster.com/Exams/Random?qNo3DqD5EpTNrP8E%3D boTax Exam Lesson Name: Advanced Grounding Applications Exam number: 006157RR Exam Guidelines > Exam Instructions Question 14 of 20 : Select the best answer for the question. 14. Which of the following statements about the neutral ground-strap ground fault protection system is correct? O A. It can be installed only at the main service equipment. O B. It monitors only the phase conductors. O C. It monitors the grounding electrode conductor at the utility connection. O D. It monitors the equipment grounding conductor and a single phase conductor. O Mark for review (Will be highlighted on the review page) > 111
Two motors A & B are to be stopped. Motor A is stopped by simply turning off the supply. Motor B is stopped by dynamic breaking. Which statement below is true * Motor A & motor B will stop at the same time Motor A stops faster than motor B Motor B stops faster than motor A
Quèstion 7 The avalanche breakdown occurs at a lower voltage compared to zener voltage. True False A Moving to another question will save this response.
QUESTION 15 What is the minimum sized Rigid Metal Conduit we should use for the above wire run if it is 24 inches long? a 1" b 1 1/4" c 1 1/2" d 2"
21 Q2/ The one Per-unit impedaunce digram line digram 3-Phave pouser System. Draw the G: 50 MVA, 13.2 KU , Xg = 0.2 Pu Tig 30MVA , 13.2/220KU, XT,=0-1s P4 Te 30MVA, 22./11 kU, X+Z=0.15pu T3:30MVA , 13.2/132 kv, XT,=0.15P4 Tu:30MUA 132/11 KV, XTzo.15 Pu M: 70 MVA, lo.45kv, Xm =0.2 p4 Load, 53 MVA , lo.45kv, o.7 P.R (Lag) line1: 22o ku, Xline I=4oA %3D line2: 132 kv, Xlinez = 6or Te 220 132 36 Ty load 38 Select a Common base of 90MUA ,13.2kv on the generator Side
I 3R 28 - 3. + Several resistors are connected to two batteries as shown in Figure. According to Kirchhoff's rules, which of the equations given below is true for this circuit? Note: Assume clockwise directed loops.
Hi, I need your help on the following problem
A.1. Combination misalignment is caused byA. misalignment by both offset and angle.B. both shafts offset vertically.C. both shafts offset horizontally.D. both shafts being located at an angle.A.2. You can usually check for a leak in a vacuum system by looking at or feelingA. for an air flow along the piping.B. at the exhaust of the vacuum pump.C. at the vacuum gauge at the vacuum pump.D. for signs of dirt on the piping.A.3. When you measure the voltage drop across a set of contacts, you'reA. checking the quality of the contact set.B. sensing how much current is flowing in the circuit.C. measuring the equivalent motor resistance.D. checking the incoming voltages.
A simply supported beam with a span length of 45 feet is laterally supported at its ends and is subjected to the following service loads: Dead load=400 lbyft (including the weight of the beam) Live load = 1000 lbyft If Fy=50 ksi, is a W14x 90 adequate? ---
Which of the following is not a boundary condition for an SLG fault on phase 'a' of a power system?
The active component of line current in figure 1 is______. a. 12A b. 20A c. 12A d. 4A