A 230 kV transmission line has an impedance of 50 cis 78 ohms and a capacitive reactance of 1,200 ohms. It transmits the power of a base load plant. On a certain dry season, the sending end power is 150 MW at a 235 kV and 90% power factor continuously for a period of one month. If the cost of generation is 1.30 pesos per kw-hr, what is the cost of the line losses for the one-month period?

A 230 kV transmission line has an impedance of 50 cis 78 ohms and a capacitive reactance of 1,200 ohms. It transmits the power of a base load plant. On a certain dry season, the sending end power is 150 MW at a 235 kV and 90% power factor continuously for a period of one month. If the cost of generation is 1.30 pesos per kw-hr, what is the cost of the line losses for the one-month period?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.14MCQ: The instantaneous power absorbed by the load in a single-phase ac circuit, for a general R LC load...

See similar textbooks

Related questions

Q: A 50-Hz, 250-V single-phase power line has the following loads placed across it in parallel : 4 kW…

A: The solution is given below

Concept explainers

Distribution System

The final stage in the delivery of the electric power is the electric power distribution system. From the transmission system to the individual customers it carries electricity. The distribution system is connected with the transmission system and is used to lower the voltage of the transmission to medium voltage in the range of 2 kV to 35 kV with the help of transformers. This medium voltage to the distribution transformers located near the customer's premises is carried by the primary distribution system lines. These distribution transformers in turn lower the voltage to utilization voltage used in lightings, household appliances, industrial equipments etc. Through secondary distribution lines often several customers are supplied from one transformer. It is through service drops, the commercial and residential customers are connected to the secondary distribution system lines. Customers who demand a larger amount of power can be connected directly to the primary distribution system level or the sub-transmission level.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Transkrmers phase with each bank with - adjuste 35. Three single-phase transformers, cach of 100 kVA rating, are conected in a closed-delta arrangement. If one of them is taken out, it would be possible to load the bank in such a manner that cach one is loaded to the extent of: A 86.6 kVA C. 57.7KVA B. 66.7 kVA D. 33.33 kVA when load is at unity power factor. 36. Average power factor at which V-V bank separate is A 86.6% C. 66.67% В. 73.3% D. None of these 37. Scott connections are used for: A. single-phase to three-phase transformation C. three-phase to two-phase transformation B. three-phase to single-phase transformation (D Any of the above 38. The current in low voltage winding of a 25 kVA, 6600/400 V, 50 Hz, 3-phase Y-A transformer, at full load is: A 36 A Č. 65,32 A B. 20.78 A D. 40.2 A 39. The current in high voltage winding of a 20 kVA, 2200/220 V, 50 Hz, 3-phase A-A transformer, at full load is: (A. 3.03 A C. jo.5 A B. 5.25 A D. None of above 40. The current in low voltage…
Q2: The constants of a 275 KV transmission line are A = 0.8525° and B = 200275° 0/phase. Draw the circle diagram to determine the power and power angle at unity power factor that can be received if the voltage profile at each end is to be maintained at 275 KV. What type a rating of compensating equipment will be required if the load is 150 MW at unity power factor with same voltage profile. (5.5 mark)
electrical engineering department plzz solve
A three phase 60 Hz transmission line delivers 750 KW at 95% leading power factor and at delta voltage of 6,900 volts. The resistance per conductor is 4.3 ohms and the reactance per conductor is 2.6 ohms. Assuming both source and load are wye connected, what is the load impedance per phase? A. 69 ohms B. 64.5 ohms C. 72.2 ohms D. 60.27 ohms
Solve for B to E Answers: a. 2247.8405 Ab. 407.5109 kVc. 2103.3334 Ad. 730.07424 MW, 449.072 MVAR (ind), 857.1313 MVAe. 30.07424 MW
The length of a three-phase power transmission line with a nominal operating voltage of 69 kV is 16km. The impedance of the transmission line per unit length is 0.125 + j0.4375 ohm/ km. At the end of the line, a 70 MVA star connected load with a power factor of 0.8 back under 69 kV interphase voltage is fed. Capacitive circuit element with a capacitance of 19.14 mikro F / phase is placed as shunt at the end of the transmission line. According to these given; a) Line head voltage and current, b) Calculate the active and reactive power per line.
Solve it quickly please
2. A three-phase transmission line has parameters Xc-6 k 2, R-3.25 2 and X₁-25 92, and delivers 300 MW to a load with both ends of the line at 230 kV. Draw a pi equivalent per-phase circuit of the line. On a per-phase basis, calculate the active power delivered to the load, the reactive power of the line and the active power delivered by the source. Based on these calculations can the equivalent circuit be simplified further?
5. A substation receives 4,500 kW power at 0.9 p.f. lag. at 10 kV from a generating station over a transmission line of impedance 6+j20 ohms/phase. Identical transformer of 30/10 kV ratio are installed at each end of the line, the transmission line voltage is 30 kV. The equivalent impedance of each transformer on HV side is 2 + j8 ohms/phase. What is the voltage at the generating station busbars?
Hey i have less time i want this solution please help me
Q2) A 13.2-kV single-phase generator supplies power to a load through a transmission line. The load's impedance is Ztoad 500 236.87° ohm , and the transmission line's impedance is Zine = 60 253.1° ohm. To reduce transmission line losses to 0.0103 of its losses without using the transformers design and use two transformers T1 between the generator and the transmission line and T2 between the transmission line and the load.
Q2) A 13.2-kV single-phase generator supplies power to a load through a transmission line. The load's impedance is Zload = 500 236.87° ohm, and the transmission line's impedance is Zline = 60 253.1° ohm. To reduce transmission line losses to 0.0103 of its losses without using the transformers design and use two transformers T1 between the generator and the transmission line and T2 between the transmission line and the load.