110 ohms. Calculate the speed at which the motor runs, if (i) 1.5 ohm resisterwere introduced in series with the armature, (iii) 300 ohms resister wereconnected in series with the field winding, and load torque remaining the samethroughout. Assume that field is proportional to field current.5. A 220 V shunt motor has armature and field resistance of 0.2 Q and 220 Orespectively. The motor is driving a constant load torque and running at 1000rpm drawing 10 A current from the supply. Calculate the new speed andarmature current if an external armature resistance of value 5 Q is inserted inthe armature circuit. Neglect armature reaction and saturation. (793.96 rpm)6. A 220 V d.c series motor has armature and field resistances of 0.15 N and 0.102 respectively. It takes a current of 30 A from the supply while running at1000 rpm. If an external resistance of 1 2 is inserted in series with the motor,calculate the new steady state armature current and the speed. Assume the loadtorque remains constant.( 858.8 rpm)7. When a generator is being driven at 1,200 rpm, the generated emf is 125 volts.Determine the generated emf (a) if the field flux is decreased by 10 percentwith the speedremaining unchanged, and (b) if the speed is reduced to 1,100rpm, the field flux remaining unchanged.( 112.5 volts, 114.6V)8. A shunt motor runs at 1200 rpm on a 420 V circuit and current taken in 30 A inaddition to the field current. What resistance must be placed in series witharmature in order that the speed may be reduced to 600 rpm, the currentthrough the armature remaining same.ra = 32 given. (5.5 2)9. A 220 V DC series motor is running at a speed of 800 rpm and draws 100 A.Calculate at what speed the motor will run when developing half the toraue

We are authorized to answer one question at a time, since you have not mentioned which question you…

A 220 V shunt motor has armature and field resistance of 0.2 2 and 220 2 respectively. The motor is driving a constant load torque and running at 1000 rpm drawing 10 A current from the supply. Calculate the new speed and armature current if an external armature resistance of value 5 N is inserted in the armature circuit. Neglect armature reaction and saturation. (793.96 rpm)

A 220 V shunt motor has armature and field resistance of 0.2 2 and 220 2 respectively. The motor is driving a constant load torque and running at 1000 rpm drawing 10 A current from the supply. Calculate the new speed and armature current if an external armature resistance of value 5 N is inserted in the armature circuit. Neglect armature reaction and saturation. (793.96 rpm)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A220 Vshunt DC motor rotates with speed of1800rev/min.( need handwritten only ,otherwise downvote.)
w3
A 500 V shunt motor runs at its normal speed of 250 rpm with an armature current of 200 A. The resistance of armature is 0.12 02. Calculate the speed when a resistance is inserted in the field, reducing the flux to 80% of normal value, and the armature current is 100 A.
Q2- A 6 pole lap connected DC generator has 480 turns ,the resistance of each turn is 0.03 Q, the flux per pole is 0.042 Wb and the machine is driven at 1200 rpm. Find E, and terminal voltage at full load armature current of 45 A
Question4 A 120-V series motor runs at 2000 rpm at full load and takes a current of 12A. The armature resistance is 0.3 ohms and the series field resistance is 0.2 ohms. A diverter resistance of 0.2 ohms is connected across the series field, and the load on the motor is adjusted. If the motor now takes 20A, what is the new speed of the motor, determine the torque developed in each case.
This course O d. None The flux o in a 18 KW, 120 V, Duplex Lap-Wound DC machine has been set to induce rated voltage at a speed of 1500 RPM. Find the product Ko, and find the induced torque in this machine at no load. Select one: O a. Product = 0,764, and Induced Torque = 114.6 N.m. O b. None Oc. Product = 0.764, and Induced Torque = 0 N.m O d. Not enough information is given to find the torque INEXT Dur
A 4 pole10V, DC shunt motor operates on a load current 10A, having wave connected armature with 200 conductors. The flux per Pole is 25 m Wb. Resistance of shunt field winding is 1 ohm and resistance of the armature is 0.15 ohm. a) what would be the back emf?
4. A shunt motor designed to operate at 115 V, has an armature resistance is 0.12 ohms and the motor is taking 60 A in armature current at full load. Determine the value of the external resistance to be inserted in the armature circuit so that the armature current shall not exceed twice its full load value at starting. A. 0.838 ohm C. 0.667 ohm B. 0.919 ohm D. 0.733 ohm
Q1. (A)- A series DC motor runs at 600 r.p.m drawing a current of 52A when connected to 220 V supply. The total resistance of the machine is 0.14 2. Calculate the value of the external resistance to be connected in series with the motor circuit to reduce its speed to 400 r.p.m. Assume the load torque is decreased to half of the previous value. Consider the field flux is proportional to armature current.