A 200kg machine is attached to the end of a cantilever beam of length L=2.5m, elastic modulus E=200x10° N/m², and the cross sectional moment of inertia l= 1.8 x 10- m. Assuming the mass of the beam is small compared to the mass of the machine, what is the stiffness of the beam?

A 200kg machine is attached to the end of a cantilever beam of length L=2.5m, elastic modulus E=200x10° N/m², and the cross sectional moment of inertia l= 1.8 x 10- m. Assuming the mass of the beam is small compared to the mass of the machine, what is the stiffness of the beam?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In the diagram below, The raccoon has a mass of 40kg and is 5m from the hinge. The beam is 8m long and is 6kg. The cable is 2m long. The beam has a diameter of 8cm. a) What are the horizontal and vertical forces on the hinge? b) What is the shear force from the cable on the beam?
Fixed/built-in or encastré beams are usually used in structure due to their high stability and performance in resisting shear stress and bending moment. Your role in building and construction company is to analyse the shear force and bending moment in order to provide better design of such beams under variety of loads. Your manager asked you to provide a complete analysis as well as to deliver a report including your design recommendations. 100 KN/m 150 kN z (m) 5 7 10 Figure.2: Encastré beam under variety of loads Your tasks are as follows: 1- Construct free-body diagram (FBD) to show the reaction forces and moments, equivalent force of the distributed load., knowing that the upward reaction force on left side is 250 kN and the reaction moment is clockwise with a value of 1500 kN.m. 2- Show FBD for each required section/cutting, include the internal forces and moments. 3- Write the distribution functions of the shear force and bending moment for each cut in the beam. 4- By hand…
A beam ABC is supported by both a uniformly distributed load and a concentrated load as indicated onthe sketch. The beam is 9 meters long. a) Calculate the bearing reactions for the beam.b) Establish the equations for the moment diagram for the beam.c) Establish the equations for the shear force diagram for the beam.d) Draw the diagrams to scale
A wooden beam is loaded by a distributed load w = 5 N/mm as shown in Figure Q4(a). The cross-section of the beam is shown in Figure Q4(b). Assume that LAB = 1600 mm, LBC = 3400 mm, W=190 mm, Bo = 20 mm, and H = 200 mm, ho=40 mm. Units: use N, mm, MPa as consistent units for all calculations. Decimal points: any decimal points are fine and all the numerical questions have a 10% error tolerance. (a) (b) hol Во H B LAB LBC Cross-section W Figure Q4: (a) A wooden beam is loaded by a distributed load, (b) cross-section of the beam.
c) Calculate the equations of internal shear force V(x) and bending moment M(x). Type the mathematical expressions or constants, following the defined sign convection. Section AB: Internal shear force equation: V(x) = Internal bending moment equation: M(x) : Section BC: Internal shear force equation: V(x) Internal bending moment equation: M(x) = = N N N*mm N*mm
Weight of forearm = 1.6kg ● Center of mass (COM) = 18cm from elbow Weight of load held: 15 kg • Forearm length: 36cm a) What is the elbow's reactive force? b) In what direction is the force of the elbow's reactive force? Positive or negative c) Demonstrate how you found the elbow's reactive force d) What is the moment at the elbow (in Newton meter)? e) In what direction is the moment at the elbow? Positive or negative
QUESTION 4 There are 47 dowels - 10M, each measuring 910 mm, in a continuous concrete footing. What is the total rebar weight (kg)? (The mass of 1OM is 0.785 kg/m): QUESTION 5 The total length of a concrete beam (400mm X 600mm) is 10,427 mm. there are stirrups 10M@200mm on centre in this beam and the concrete cover is 25mm. How many stirrups does this concrete beam have?
The load condition and section of the beam given above;a) Draw the shear force and bending moment diagrams.b) Find the maximum and minimum normal stress in the beam.c) For the loading condition given that the beam material is concrete (brittle material),Check whether there is a break or not.
machine design
Question 3 A simply supported beam with the boundary conditions as shown. An applied load, F is acted at the center of the beam and causes a deflection, y in meter. Using the value from the Table to plot a graph and using the moment of area and cantilever beam theory to determine the value of Young's Modulus, E of the beam in N/m². The following data are obtained in a simple experiment: F(N) y(m) 0 0 2.45 0.00043 Given that the moment of area, I=4.572x 10-10m4 The length of the beam, L = 0.25m FL3 According to the cantilever beam theory: y = - 48EI 14.71 4.9 7.36 9.81 12.26 0.00087 0.00131 0.00175 0.00218 0.00262 F L/2 40 Points I www
A.) It is the boundary condition for fixed support Choices: Both choices Y=0 Y’=0 Either of the choices B.) It is a type of simple stress acting parallel to an area Choices: Flexural stress Shear stress Axial stress Bearing stress C.) For concentric row of bolts in a coupling connection, the shear deformations in the bolts is proportional to the: Choices Modulus of rigidity Diameter of bolt circle Radial distance Number of bolts note: please help us in the word meaing sample problems thank you
For the simply-supported and cantilever beams given below, use Singularity Functions to determine slope and displacement equations. Provide graphs of both slope and displacement versus position along the beam. A A 5 ft B * B 5 ft 5 ft 27 kips E 20 ft 45 kip-ft 11 kips 5 ft 3.5 kips/ft 20 ft C 5 ft 5 ft 2.3 kips/ft 5 ft ]c S ft D