A 20 MVA, 11.2 kV, 4-pole, 50 Hz alternator has an inertia constant of 15 MJ/MVA. If the input and output powers of the alternator are 15 MW and 10 MW, respectively, the angular acceleration in mechanical degree/s² is (round off to nearest integer)

Q: Question No. 12: a.) Explain the Gas turbine power plant with neat sketch. b.) Draw and explain the…

A: Step-1->A power generating plant which has gas turbine as the prime mover for the generation of…

Q: The indication of a lagged demand meter approaches the value of the actual load at a rate which is…

A: Concept- A lagged demand meter- The pointer is made to move in the electromechanical thermal or…

Q: Draw the output signal Q of the D-latch given the inputs Clock and D. The initial value of the clock…

A: Given:

Q: Discuss the concept of load shedding and its purpose in a power system.

A: Load shedding is a controlled and deliberate reduction in electrical power supply to certain areas…

Q: Current Transformer is used to step up the current of power system. Select one: True

A: Current transformer is a step down transformer. It always step down the current.

Q: 4) Draw a circuit diagram of a Static Synchronous Series Compensator (SSSC) and gives his…

A: It is asked to solve subpart 4,5 and 6.   There are different types of FACTS controller which are…

Q: ist out all the major components in a thermal power plant

A: Answer: All major components in a thermal power plant.

Q: Briefly explain three(3) side effects of the addition of power generation units and their remedies.

A: Nowadays Electricity is a major part of any country's growth. The demand for power supply is…

Q: write an objects for three-phase system with load on transformer (open and short circuit )

A:

Q: One type of linear reglator of power supply is known as A.strict regulator B.cheap regulator…

A: Voltage regulator is required to get steady, reliable and constant voltage. Voltage regulator may…

Q: bioconversion process produces Biogas, ethanol etc.

A: In this we will write about bioconversion proces which produces biogas.....

Q: Classification of 1200 MWe capacity natural gas power plant

A: We need to tell about classification of 1200 MWe capacity natural gas power plant.

Q: Identify the position of plunger in a LVDT in which emf induced in upper secondary coil is equal to…

A: we need to choose the correct option for the given statement.

Q: 8- What are the advantage of use of (G- M) system and in which cases i is recommended?

A: In terms of electrical, GM system stands for Generator Motor system. GM sets are used to convert…

Q: 1. Explain the reasons for the low power factor in the power system network

A: Power factor (PF) is the ratio of working power, measured in kilowatts (kW), to apparent power,…

Q: List out all the major components in a thermal power plant

A: The thermal power plant is used to produce electricity by utilizing the energy of the burning fuel.

Q: b) A1000 MW turbine generated 648 MWh during 30 da What would is capacity factor be?

A: In this question we will find capacity factor of turbine...

Q: The REPET-UNTIL high level language statement executed in assembly in the following segment program:…

A: Count value stored in register CL in step 1 And the loop will executed until it becomes zero. Hence…

Q: 9V DC DC 230V step-down transformer Bridge rectifier Capacitor Filter voltage regulator Voltage…

A:

Q: Which of the following type will be mostly adopted in case small hydropower systems? O a.…

A: In case of pumped storage hydropower plant and Reservoir hydropower plant, a dams or big reservoirs…

Q: Give any five comparisons between Gas power plants and Thermal power plants

A: The gas power plant and thermal power plant differs on many aspects like output production,…

Q: What is water circulating system in hydro conventional energy system.

A:

Q: ) Wind farm consist of ten wind turbines with nominal capacity of 2MWper turbine, has a total of 20…

A: Capacity factor =Average load / installed capacity. Average load = no. Of units produced / no. Of…

Q: Ring main distributor cannot be used both in DC and AC distribution system. Select one: O True O…

A: False  Ring main distribution used for both ac and dc

Q: e a short note on production and consumption pattern of primary energy in India.

A: production pattern of primary energy in India : In India most of the primary energy about 75 % to…

Q: 5. A three-phase rectification system has a voltage ripple of 14%. If the output kVp is 150, what is…

A: Given data, Output voltage VO=150 V. Ripple voltage Vr=14 %.

Q: For controlled half wave rectifier, R=80ohm, f=50Hz and Vm=280V and a=0,2 rad. Calculate the average…

A: It is given that: R=80 ohmf=50 HzVm=280 Vα=0.2 rad=0.2×180π=11.46°

Q: : Answer only one of the following: A- What are the advantages of a diesel power station?

A: Power station- A power station or a power plant is a unit where electricity is generated using some…

Q: ?The open circuit test results in finding which of the following parameters 1. core losses II. shunt…

A: Open circuit test : Open circuit test is used to determine the, 1. Core losses. 2. Shunt branch…

Q: 1. For unsymmetrical analysis in power system why we use operator a? 2. In Delta connected load,…

A: 1. The operator "α"  stands for an abbreviation for showing a difference phase shift of 120 degrees.…

Synchronous Motor

The synchronous motor is an AC electric type motor where at a steady-state the shaft rotation is synchronized with the supply current variable-frequency. To an integral number of AC cycles, the rotation period is exactly equal. The stator of the motor in the synchronous motor contains multi-phase AC electromagnets due to which a magnetic field is created that rotates in time with the oscillation of the line current. The rotor contains a permanent magnet and the rotor rotates in synchronization with the stator field at the same rate and provides the second synchronized magnetic field which is rotating in nature as a result. When the synchronous motor is supplied with independently excited multi-phase AC electromagnets on both the rotor and the stator, it is termed as a doubly-fed machine. The most widely used AC-type motors are the synchronous AC motor and the induction AC motors.