A 2.25 m long solid bar (Lo) with a 32 mm diameter is placed under tension by a load (F) of 250 kN. The bar is solid and made of a homogeneous material with a Young's Modulus E = 250 GPa. Calculate the extension of the bar (AL). Give your answer in millimetres (mm) to two decimal places. Lo AL F F L

A 2.25 m long solid bar (Lo) with a 32 mm diameter is placed under tension by a load (F) of 250 kN. The bar is solid and made of a homogeneous material with a Young's Modulus E = 250 GPa. Calculate the extension of the bar (AL). Give your answer in millimetres (mm) to two decimal places. Lo AL F F L

Physics for Scientists and Engineers

10th Edition

ISBN:9781337553278

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter18: Temperature

Section: Chapter Questions

Problem 16P: Review. On a day that the temperature is 20.0C, a concrete walk is poured in such a way that the...

See similar textbooks

Similar questions

The lintel of prestressed reinforced concrete in Figure P12.27 is 1.50 m long. The concrete encloses one steel reinforcing rod with cross-sectional area 1.50 cm2. The rod joins two strong end plates. The cross-sectional area of the concrete perpendicular to the rod is 50.0 cm2. Youngs modulus for the concrete is 30.0 109 N/m2. After the concrete cures and the original tension T1 in the rod is released, the concrete is to be under compressive stress 8.00 106 N/m2. (a) By what distance will the rod compress the concrete when the original tension in the rod is released? (b) What is the new tension T2 in the rod? (c) The rod will then be how much longer than its unstressed length? (d) When the concrete was poured, the rod should have been stretched by what extension distance from its unstressed length? (e) Find the required original tension T1 in the rod. Figure P12.27
Artificial diamonds can be made using high-pressure, high-temperature presses. Suppose an artificial diamond of volume 1.00 106 m3 is formed under a pressure of 5.00 GPa. Find the change in its volume when it is released from the press and brought to atmospheric pressure. Take the diamonds bulk modulus to be B = 194 GPa.
Assume Youngs modulus for bone is 1.50 1010 N/m2. The bone breaks if stress greater than 1.50 108 N/m2 is imposed on it. (a) What is the maximum force that can be exerted on the femur bone in the leg if it has a minimum effective diameter of 2.50 cm? (b) If this much force is applied compressively, by how much does the 25.0-cm-long bone shorten?
Review. On a day that the temperature is 20.0C, a concrete walk is poured in such a way that the ends of the walk are unable to move. Take Youngs modulus for concrete to be 7.00 109 N/m2 and the compressive strength to be 2.00 109 N/m2. (a) What is the stress in the cement on a hot day of 50.0C? (b) Does the concrete fracture?
A 100-N weight is attached to a free end of a metallic wire that hangs from the ceiling. When a second 100-N weight is added to the wire, it stretches 3.0 mm. The diameter and the length of the wire are 1.0 mm and2.0 m, respectively. What is Young’s modulus of the metal used to manufacture the wire?
A copper rod with length 1.4 m and cross-sectional area 2.0 cm2 is fastened to a steel rod of length L and cross-sectional area 1.0 cm2. The compound structure is pulled on each side by two forces of equal magnitude 6.00 104 N (Fig. P14.57). Find the length L of the steel rod if the elongations (L) of the two rods are equal. Use the values Ysteel = 2.0 1011 Pa and YCu = 1.1 1011 Pa. FIGURE P14.57
A certain hydraulic system is designed to exert a force 100 times as large as the one put into it. (a) What must be the ratio of the area of the slave cylinder to the area of the master cylinder? (b) What must be the ratio of their diameters? (c) By what factor is the distance through which the output force moves reduced relative to the distance through which the input force moves? Assume no losses to friction.
Use the graph in Figure P14.46 to list the three materials from greatest Youngs modulus to smallest. Explain your reasoning. FIGURE P14.46
Alarge uniform cylindrical steel rod of density =7.8g/cm3 is 2.0 m long and has a diameter of 5.0 cm. the rod is fastened to a concrete floor with its long axis vertical.what is the normal stress in the rod at the cross-section located at (a)1.0 mfrom its lower end?(b)1.5 m from the lower end?
(a) When water freezes, its volume increases by 9.05% (that is, V/V0=9.05102 ). What force per unit area is water capable of exerting on a container when it freezes? (It is acceptable to use the bulk modulus of water in this problem.) (b) Is it surprising that such forces can fracture engine blocks, boulders, and the like?
A disk between vertebrae in the spine is subjected to a shearing force of 600 N. Find its shear deformation, taking it to have the shear modulus of 1109 N /m2. The disk is equivalent to a solid cylinder 0.700 cm high and 4.00 cm in diameter.
Bone has a Young's modulus of about 18 ✕ 109 Pa. Under compression, it can withstand a stress of about 157 ✕ 106 Pa before breaking. Assume that a femur (thigh bone) is 0.45 m long, and calculate the amount of compression this bone can withstand before breaking. in mm