A 2.2 KVA, 480/4800-V, 50 Hz, single-phase transformer is tested with the following results. Find the impedance referred to the HVS of the transformer. SCT measured from LVS Ver = 24 V SC Isc = 4.5 A Per = 36 W SC Select one: O a. Regs = 1.8 N, and Xeq,s = 5.03 Q O b. Rc.p = 1.8 N, and XM,p = 5.03 Q %3D O c. Regs = 180 Q, and Xeg,s = 503 Q %3D %3D O d. None

A 2.2 KVA, 480/4800-V, 50 Hz, single-phase transformer is tested with the following results. Find the impedance referred to the HVS of the transformer. SCT measured from LVS Ver = 24 V SC Isc = 4.5 A Per = 36 W SC Select one: O a. Regs = 1.8 N, and Xeq,s = 5.03 Q O b. Rc.p = 1.8 N, and XM,p = 5.03 Q %3D O c. Regs = 180 Q, and Xeg,s = 503 Q %3D %3D O d. None

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

opper losses Which of following is a variable loss in a transformer? O Constant loss O Eddy current Hysteresis losses O Copper loss
Solve it quickly please
VOLTAGE STEP UP THE VOLTAGE TRANSFORMER Done Choose... STEP UP THE CURRENT STEP UP THE VOLTAGE FREQUENCY PHASE DIFFERENCE
Help me review this example
Draw a block diagram of a power supply from transformer up to regulator with corresponding waveform.
In no load phasor diagram of practical transformer, the magnetizing current Imag is with flux Ø O Leading by 30° O Lagging by 60° In phase O 90° out of phase
How does the coupling factor affect the primary and secondary voltages? For example if the turns ratio in my transformer is 1:2 and the Vin is 10V, the voltage on the primary side is 10V and the voltage on the secondary side is 20V when the coupling factor (k) is 1. What will the primary and secondary voltages be if the coupling factor becomes 0.5?
A single phase 220/6 Volt, 50 Hz transformer has a rated primary current = 0.5 A. its maximum efficiency is at load current = 15 A and equal to 94% at unity p.f. Its efficiency at rated load, 0.65 p.f. lagging is: 087.8%. 092.3%. 090.9%. ONone.
A single phase transformer has a 600 turns in the pri- mary and 1200 turns in the secondary. The cross sec- tional area of the core is 905 sq.cm. If the primary winding is connected to a 50 Hz supply at 400V. The peak flux density is wb/m²
In no load Phasor diagram of practical transformer, the core loss current Ic is with primary voltage Vp. O Lagging O in phase O Leading O 90 degrees out of phase
In a practical transformer, Identify, which component of no load current supplies eddy current loss? a. I0 b. IC c. IM d. None of these
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across R, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diodeshave? (Use constant voltage drop model for the Silicon diode) D IN4001 OV 10 kN IN4001 DELL