A 2-wire d.c. distributor 81 m long at a distance of 59 m is uniformly loaded with 0.26 A/m.Resistance of single wire is 0.00089 2 /m. If the distributor is fed at one end.CalculateThe voltage drop up to a distance 59 m from the feeding point =The total resistance=

a) Voltage drop=IRVoltage drop at 1 meter V1=0.26×1×1.78×10-3×1Voltage drop at 2 meter…

A 2-wire d.c. distributor 81 m long at a distance of 59 m is uniformly loaded with 0.26 A/r Resistance of single wire is 0.00089 /m. If the distributor is fed at one end. Calculate The voltage drop up to a distance 59 m from the feeding point

A 2-wire d.c. distributor 81 m long at a distance of 59 m is uniformly loaded with 0.26 A/r Resistance of single wire is 0.00089 /m. If the distributor is fed at one end. Calculate The voltage drop up to a distance 59 m from the feeding point

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

b) Explain why the effective length is less than the lotal length of a laminated armature .Which value should be used for L in Ecotl DLN»B and Trol- NDLIcoB? Which value should be used in resistance calculations?
Q3) The self capacitance of each unit in a string of four suspension insulators is C. The shunting capacitance of the connecting metal work of each insulator to earth is 0-2 C. Calculate (i) the voltage across each insulator and (ii) string efficiency.
An aluminum wire of unknown length has a diameter of .382 cm. and a resistance of .295 ohm. By several successive passes through drawing dies the radius of the wire is reduced to .078 CM. has increased by 23.6 % in the drawing process, calculate the Assuming its resistivity resistance of the reduced size wire.
During the Wheatstone Bridge experiment, when the pointer is at the balance point then: O a. The potential difference across the unknown resistance is equal to the potential difference between the end of the wire connected to the known resistance.the balance point. O b. The potential difference across the known resistance is equal to the potential difference between the balance point and the point of contact between the known andunknown resistances. O c. The potential difference across the unknown resistance is equal to the potential difference across known resistance. O d. The potential difference across the unknown resistance is equal to the potential difference between the balance point and the end of the wire connected to the unknown resistance. O e. The potential difference across the unknown resistance is equal to the potential difference between the balance point and the end of the wire connected to the known resistance. Clear my choice
6/ The Design of Distributors depend on which parameter? A. CURRENT CARRYING CAPACITY B. HIGH POWER CAPACITY C. LOW VOLTAGE DROP TENDENCY D. CONSTANT VOLTAGE MODE
A 6 ampere supply has a frequency of 25 Hz. Find the instantaneous value of current a. at 0.00986sec from zero going to the positive direction. b. at 0.00986 sec from zero going to the negative direction. c. at 986 degrees. Show complete solutions.
A 2-wire d.c. distributor 300 metres long is uniformly loaded with 4A/metre. Resistance of single wire is 0.3 ohm/ km. If the distributor is fed at one end, calculate the voltage drop upto a distance of 140 m from the feeding point
A patient is connected to a pressure monitor by way of a catheter. Resistance of catheter is 6000 Q. Dirt and grime make a resistance path from the catheter to H wire of 500,000 Q. The H wire is plugged into a 240 V power bus. Calculate the leakage current that could pass into the heart of the patient. Is the patient might or might not have shock? Assume a viscera resistance of 200 Q.
3. A 250 m, 2-wire d.c. distributor fed from one end is loaded uniformly at the rate of 0-8 A per metre. The resistance of each conductor is 0.0002 2 per metre. Find the necessary voltage at the feeding point to maintain 250 V at the far end of the distributor. [260 V]
2. When a current of 1A flows through a wire, the drift velocity of the electrons is 0.9 mm/s. What will be the drift velocity of the electrons when a 2A current flows through another wire of the same material having double the length and double the area of cross section and same temperature.
12. You plot the current-voltage characteristics of a new non-ohmic device, perform a curve fit, and discover the current as a function of voltage is given by the equation: I = (9Amp/volt")V² – (7Amp/volt) V (a). Perform calculations to find the slope of a line tangent to this curve when V = 4.15 volts. (b). Calculate the effective resistance of this device when V = 4.15 volts. This device is Non-Ohmic!
For the network shown in Figure B22 , assume E = 18V, Diode D¡ as silicon and D2 Germanium, R1=3KQ and R2=2K2. Calculate, i. Current I,, ii. Current In2 ii. Voltage across resistor R2 R1 D E D2 R2 Figure B22 +