A 2-storey office building has interior columns that are spaced 6.71m apart in 2 perpendicular directions. If the (flat) roof loading is 1kN/m2, determine the reduced live load supported by a typical interior column located at ground level. How about 6 storeys? エー AT 6.71 m エ+ 6.71 m -6.71 m- -6.71 m Fig. 1-9 H-

A 2-storey office building has interior columns that are spaced 6.71m apart in 2 perpendicular directions. If the (flat) roof loading is 1kN/m2, determine the reduced live load supported by a typical interior column located at ground level. How about 6 storeys? エー AT 6.71 m エ+ 6.71 m -6.71 m- -6.71 m Fig. 1-9 H-

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The school building has a flat roof. It is located in an open area where the ground snow load is 0.68 kN/m2. Determine the snow load that is required to design the roof.
Subject: Reinforced concrete Design- Civil Engineering A rectangular beam reinforced for tension has b = 300mm, d = 480mm. The beam is reinforced with 7 of 25mm bars with fc' = 21MPa and fy = 415MPa. If the beam is cantilever, 3m long and supports a uniform dead load of 15kN/m (including its own weight) applied along its entire length, the maximum value of the concentrated live load that can be applied 2m from the free end is kn. Choices: A. 141kN B. 114KN C. 213kN D. 231kN
A two-storey school (use classroom) has interior columns that are spaced in 4.5 meters apart in two perpendicular direction. If the loading on the flat roof is estimated to be 1 kN/m^2. Determine the live load supported by a typical interior column at the ground floor level in KN. (Consider reduced live load where applicable)
Colum A and Column B are spaced at 2.5m apart and are carrying the nominal loads tabled below. Left Colum/ Column A Right Column/ Column B Dead Load, G/D Imposed live load, Q/L 2.5m ? Column A Working pressure = Total working load on the base, Ptotal = kN/m² 4.5m Left Column/Column A = Right Column/ Column B = Base thickness is 500mm and the permissible working pressure is 150kPa Ultimate ground Pressure, Put 2.5m 1.1. Determine the centroid of the base from the left edge of the base and the working pressure Distance from the Left edge to the centroid m (round off to 3) UDL on beam-in-slabi 400KN 550KN KN 1.2. Determine the ultimate shear Force and the ultimate bending moment on column A Ultimate loads on column KN Column B kN/m KN kN/m or kPa. Maximum shear at Support A/LHS support = Maximum Moment at Support A/LHS support 350KN 250KN KN kNm
A building wall consists of exterior stud walls with brick veneer and 13 mm fiberboard on one side. If the wall is 4 m high, compute the load (kN/m) that it exerts on the floor SARLE 1-M Dval Fler F C
Question 3 The wind blows uniformly on the front surface of the metal building with a pressure of 1.8 kN/m?. Determine the resultant force it exerts on the surface and the position of this resultant. y 2.5 m 1.0 m 2.5 m. 2.5 m.
Given the following beam, determine: 1. Deformed, Shear Diagram and Moment Diagram 2. Deformed Equation 3. Slope Equation 4. Reactions 5. Maximum effort (σ_max) 6. Maximum shear (τ_max)
Find the collapse load for the truss shown in the figure. All three bars have the same plastic axial strength 125 kN. 5.40m 9.60m D C 7.20m А
The floor of a wholesale store building is made of 100 mm thick cinder concrete. If the floor is a slab having a length of 3m and width of 2.5m, determine the resultant force in kN caused by the dead load and the live load.
1. Design the spacing of the main bars and temperature bars of a one-way slab having a total span of 5 m. The slab is supported with hinge in the left support and a vertical cable located 1.5 m from the right support. The distance between the cables of the slab is 2.3 m. The slab is to carry a live load pressure of 2.4 kPa and a dead load pressure (including self-weight) of 4 kPa. Assume f'c = 27.6 MPa and fy = 276 MPa for main and temperature bars. Use 12 mm Ø for main bars and 10 mm Ø for temperature bars. The slab is not exposed to earth or weather. Use thickness of slab of 120 mm. Use NSCP 2001.
Concrete T-beam has been reinforced by bonding a steel plate to its web asshown below. The beam carries a uniformly distributed load of 40kN/m overa simply supported 8m span. Find the maximum deflection of the beam onthe assumption that the concrete is fully operative in both tension and compression.(Est = 200kN/mm2. Econc = 30kN/mm2; central deflection due uniformly distributedload, total W acting on a simply supported beam of span L is 5WL3/(384EI))
A two-story office building shown in the photo has interior columns that are spaced 22 ft apart in two perpendicular directions. If the (flat) roof loading is 20 lb/ft2, determine the reduced live load supported by a typical interior column located at ground level.