A 2 4 6 8 10 ܘ܂ B 12 14 A 14 ft long beam is subjected to a load which varies uniformly from 50 lbs/ft at C to 75 lbs/ft at D. Assume the weight of the beam itself is 50 lbs/ft. Find Reactions Determine the reactions at A and B. A = 590lbs × B = 19.4lbs

Q: Required information The state of stress at a point is ox= 19 kpsi, oy= 0 kpsi, oz= 19 kpsi, Txy= 38…

A:

Q: In (Figure 1), r= 60 mm. Figure 50 mm 100 mm 100 mm 50 mm 150 mm ▼ Locate the centroid of the metal…

A:

Q: Need help with this  Mechanics of Materials review  How to draw the element with the numbers (c)…

A: Given

Q: how did we go from 9.3kN to 7.5 kN for the load applied?

A:

Q: Determine the reactions needed to support the load. Please, present your work in organized and neat…

A:

Q: Take P= 38 kN. EI is constant. (Figure 1) Figure 4 m B- 2 m- P 1 of 1 Determine the y-component of…

A: Determine the y-component of the reaction at the roller B.Determine the x component of the reaction…

Q: The assembly is the same as in problem 2. It consists D of two rods AC and BD attached to the 100-lb…

A:

Q: What is the entire area under the stress-strain diagram called?

A: The graphical representation of the stress developed in a material due to the application of the…

Q: If we use a 4340; 4140; 8640; 5140; 1040 steel, what would be the hardness number at the center of…

A: First go to Figure below and draw a horizontal line from 1.5 in. diamater and intersect it with…

Q: If 14 MPa lateral pressure is applied to a cylinder concrete sample with characteristic compressive…

A: No strength because the compressive pressure in longitudinal direction is 20MPa and the lateral…

Q: what is the equation and the units of measure for ductility?

A:

Q: une at F = 5.5 kN (Figur

A: solution as follows

Q: Question (5): (a) The device shown in Fig. (5-a) is designed to apply pressure when bonding laminate…

A: Given Data At the handle 120N force is applied  Let us draw the reaction at the roller supports

Q: The rigid lever arm is supported by two A-36 steel wires having the same diameter of 4 mm. Determine…

A: According to the given data D=4mm The yield stress of the A 36 steel is 250MPa L=300mm We need to…

Q: a- calculate the atomic backing factor for Bc..

A: Because the volume of each of the eight corner atoms is shared between eight adjacent cells, each…

Q: Let's consider a rod having a solid circular cross-section with diameter of 6 mm and it is made of a…

A:

Q: Locate the centroid of the area shown in the figure by direct integration. (Caution: Carefully…

A:

Q: A steel bar AD has a cross-sectional area of 260 mm² and is loaded by forces P, = 12 kN, P, = 8 kN,…

A:

Q: Aluminum Steel Q1

A: Given that, Weight is suspended from structured A-36 steel alloy and 2014 and aluminum alloy wires,…

Q: Consider the structure shown in (Figure 1). Suppose that P = 4.5 kN and P = 5.5 kN. Part A Determine…

A:

Q: GIVEN: Diagram shown below [Note: you do not have to re-create the GIVEN diagrams; work must be on…

A:

Q: The assembly is the same as in problem 2. It consists D of two rods AC and BD attached to the 100-lb…

A:

Q: 8. 10 plate 8X10 - S00 pounds of loud material 6061 Aluminum - Determine what type of stress Is…

A: Hf

Q: Please answer the attached question which includes all the necessary background information sourced…

A: The objective of the question is to find the value and location of the largest tensile and…

Q: Determine the height h above the base of the centroid of the Assume a = 10.27 in., b = 12.07 in., c…

A:

Q: Find the maximum biaxial stress,0x= -20, oy= -30, o > 0, that one can apply to a 60° lamina of…

A:

Q: A horizontal beam BC is subjected to uniformly distributed load, w and at the same time it is…

A:

Q: The rigid bar of negligible weight is supported as shown. The assembly is initially stress- free.…

A: Answer: (a) The stress in the bronze bar is 50.78 MPa. (b) The stress in the steel bar is 52.11 MPa.…

Q: Three (3) different cylinder made from Steel, Aliminum and Bronze are jointed together to form a…

A: Elongation in a bar of constant section is given as the  δl=PlAE Total elongation for this combined…

Q: 4-3. Determine the residual strength diagram (ơmax versus a) for a center-cracked panel (CCP) of…

A: RESIDULA STRENGTH To lay out the remaining strength capacity of a given design under specific…

Q: shows the state of stress at a critical point on a component of a lawn mower, wh Opx = 10 MPa…

A: Givenσxx=10Mpacompressive=-10Mpaσyy=25Mpatensileζxy=90Mpacloclwiseσzz=20MpacompressiveSyt=300MpaSyc=…

Q: three (3) different cylinder muade from Steel, Aliminurm and Uronze are jointed together to torma…

A: Given data steel Area = 500. mm2 Youngs modulus or modulus of elasticity (E) = 200 GPa = 200*109…

Q: Summarize why the shear formula does not give accurate results when applied to members having…

A: Summary:               (1)  The shear formula does not give accurate results when applied to members…

Q: 4- Draw Shear Stress-strain diagram for Cast Iron

A:

Q: A: Draw the Free Body Diagram only of next fig. A TTTTT

A:

Q: From the consideration of the stress element, the shear stresses at x-plane and y-plane must be: of…

A: There is a stress element which is in the equilibrium condition. so all the net external forces and…

Q: and (b) by cylinder B? The for cylinder A and defe

A:

Q: When rebuilding his car's engine, a mechanic must exert 300'N of force to insert a dry steel piston…

A:

Q: (1051) bonds- YouT x (1051) Majid Al Moh x…

A:

Q: :-4 ksi, he normal stresses at a point in a steel member are a, = 8 ksi, a, = 4 KSt. 10ksi. Using E…

A: Total strain along X, Y and Z directions: