25. If the pitch (s) will be equal toboth pattern, what would be thevalue of pitch (s)?a. 154.31 mmb. 125.45 mmC. 141.42 mmd. 126.48 mm SITUATION V:Refer to the figure below:150200---20010015023. Determine the net area torABCD. Thickness of plate is 10mmand the diameter of the hole is 25mm.a. 1815 mm?b. 5125 mm?c. 3725 mm?d. 2648 mm?24. Determine the net area torEFG. Thickness of plate is 100mmand the diameter of the hole is 25mm.b. 5250 mm?d. 2250 mm?a. 4850 mm?c. 3750 mm?150200

Answered: Image /qna-images/answer/aea51e2f-f0a0-46d1-beae-95a431350719.jpg

A 150 200 200 100 150 23. Determine the net area for ABCD. Thickness of plate is 10mm and the diameter of the hole is 25 mm. b. 5125 mm? d. 2648 mm? a. 1815 mm? c. 3725 mm? 24. Determine the net area for EFG. Thickness of plate is 100mm and the diameter of the hole is 25 mm. a. 4850 mm? c. 3750 mm? b. 5250 mm? d. 2250 mm? 150 200 ...

A 150 200 200 100 150 23. Determine the net area for ABCD. Thickness of plate is 10mm and the diameter of the hole is 25 mm. b. 5125 mm? d. 2648 mm? a. 1815 mm? c. 3725 mm? 24. Determine the net area for EFG. Thickness of plate is 100mm and the diameter of the hole is 25 mm. a. 4850 mm? c. 3750 mm? b. 5250 mm? d. 2250 mm? 150 200 ...

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

B9
Show FBD and complete solution please. (Round off at 3 decimal places only at the final answer)
Problem Solving : Round off your final answer to 2 decimal places. 20KN DI L4 H ! T 3m SKN ↑ 3m ↓ 4m ·0 13 G By L2 F A Barn E J * 3m 311) 3m For the frame provided below, consider the following properties: * Members along Level a Regular Hexagon with side = 300mm * Membens along Level 3 Regular Trapezoid with longer side = 500mm, shorter side = 400mm, Height = Soomm * Members along Level 4 Regular Trapezoid with longer side = 300mm, shorter side = 200mm, Height = 400mm * Members along Line 1 Hollow circular Tube, Outer Diameter = 550mm, Inner diameter = 350mm * Members along Line 2 Hollow Square Tube, Outer Breadth & Height = Soomm, Inner Breadth & Height = 300mm + Members along Line 3. Equilateral Triangle with side = 650mm + Members along Line 4 Hollow circular Tube, Outer Diameter = 400 mm, Inner Diameter = 300mm Solve the following for ALL members: 1. Axial Forces 2. Shear Forces 3. Moments
Questions T 40 mm TABLE 3.1. Coefficients for Rectangular Bars in Torsion a/b C₁ C₂ 1.0 0.208 0.1406 1.2 0.219 0.1661 60 mm 1.5 0.231 0.1958 2.0 0.246 0.229 2.5 0.258 0.249 3.0 0.267 0.263 4.0 0.282 0.281 5.0 0.291 0.291 N 10.0 0.312 0.312 0.333 0.333 1. Determine the largest torque T which may be applied to end of the solid bar which is shown in the diagram above, knowing that the maximum allowable shear stress = 107 MPa and G = 40 GPa. Provide the answer in kNm with precision to two decimal points. 2. The same solid bar is subjected to a torque of 1.5 kNm. Its total length, denoted as z, is 601 mm. What will be the angle of twist? Provide the answer in degrees with precision to two decimal points.
the value of A=382.3 , E=120 , B, 25 , AND D=9
m? 7) What is the axial stress o AB in Pa?
Find the question, thanx.
50 mm 100 mm 50 O 75 mm 100 100 50 h 75 e 9 75 a b ņ d For a failure through the staggered line abfcd, what is the gauge length (sg) of the stagger? + 75
人工知能を使用せず、すべてを段階的にデジタル形式で解決してください。ありがとう SOLVE STEP BY STEP IN DIGITAL FORMAT DON'T USE CHATGPT Design the longitudinal steel and the cross section of the beam shown, consider concrete that indicates fy = 4200 kg/(cm²), 1/2 stirrups and 2.5 cm coatings. 1m 0.5T 2m 0.2T 6.5m Calculate top rods per steel (min) asmin If f'c = 200kg/cm² 1.5T/m
show complete solutions and original work please don't copy from other sites
You measured 300 ul with a 1000ul pipette; The corrected values were the following : 292 ul, 294ul, 287ul, 290ul, 288ul and 293 ul (mean- 290.7 ul and Std. dev + 280 ul) 3. Acceptable values are: Accuracy : 1.0% Precision: 0.5 % Were you accurate? Were you precise? and why? show cakulations
Opening (mm) Sieve No. Mass Retained (g) 4 4.75 10 2. 112 20 0.85 163 40 0.425 100 60 0.25 154 80 0.18 131 100 0.15 192 200 0.075 140 Pan 61 Calculate the following: a. D10 b. D25 c. D30, d. D60' e. D75, f. Cu, g. C. h. So