A 15 kW and 1200 r.p.m. motor drives a compressor at 300 r.p.m. through a pair of spur gears having 20° stub teeth. The centre to centre distance between the shafts is 400 mm. The motor pinion is made of forged steel having an allowable static stress as 210 MPa, while the gear is made of cast steel having allowable static stress as 140 MPa. Assuming that the drive operates 8 to 10 hours per day under light shock conditions, find from the standpoint of strength, 1. Module; 2. Face width and 3. Number of teeth and pitch circle diameter of each gear. Check the gears thus designed from the consideration of wear. The surface endurance limit may be taken as 700 MPa.

A 15 kW and 1200 r.p.m. motor drives a compressor at 300 r.p.m. through a pair of spur gears having 20° stub teeth. The centre to centre distance between the shafts is 400 mm. The motor pinion is made of forged steel having an allowable static stress as 210 MPa, while the gear is made of cast steel having allowable static stress as 140 MPa. Assuming that the drive operates 8 to 10 hours per day under light shock conditions, find from the standpoint of strength, 1. Module; 2. Face width and 3. Number of teeth and pitch circle diameter of each gear. Check the gears thus designed from the consideration of wear. The surface endurance limit may be taken as 700 MPa.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Two parallel shafts are to be connected by spur gearing. The approximate distance between the shafts…

Q: A 15 kW and 1200 motor drives a compressor at 300 a pair of spur gears having . The center-to-center…

A: Given DataP=15kWN1=1200rpmN2=300rpmc=400mmσP=210MPa

Q: A 17-tooth 20° pressure angle spur gear rotates at 1800 rev/min and transmits 4 hp to a 52-toot…

A: dp=NpPd=1710=1.7 indG=5210=5.2 inV=πdp.np12=π×1.7×180012=801.1 ft/min

Q: A drive system for a large commercial band saw is to be designed to transmit 12 hp. The saw will be…

A: 1 HP = 745.7 = 746 WATT 12 HP = 12 * 746 = 8952 W = 8.952 KW pinion rotates NP = 3450 rpm gear…

Q: Problem 4. A 16-tooth 240 Bhn steel spur pinion having a pressure angle of 20° and rotating at 720…

A: Calculate the diameter of the gear. Dg=NgPg Here, Dg is the gear diameter, Ng is the number of teeth…

Q: A single stage spur gear gearbox has a module of 1.5mm and an input speed of 1500.p.m. and a pinion…

A: For the given yield stress and materials,Consider the velocity factor and service factor to be, .

Q: 13-31 Shaft a in the figure has a power input of 75 kW at a speed of 1000 rev/min in the…

A: Given, Power in shaft a = Pa = 75 kW = 75000 W Rotational speed of a = Na = 1000 rpm Module of all…

Q: solve Q a.

A: Given Data⇒V belt driveProblem definition⇒Problem says estimate initial tension for a V belt drive

Q: A 20° spur pinion with 20 teeth transmits 120 W to a 36-tooth gear. The pinion speed is 100 rev/min,…

Q: A 15 kW and 1200 r.p.m. motor drives a compressor at 300 r.p.m. through a pair of spur gears having…

A: Given, Power,P=15KWPressure angle,ϕ=20°Np=1200rpmNG=300rpmAllowable static stress of…

Q: The press shown for Prob. 8-5 has a rated load of 5000 lbf. The twin screws have Acme threads, a…

A: ( if you have any queries please feel free to ask me ).

Q: 15 kW and 1200 r.p.m. motor drives a compressor at 300 r.p.m. through a pair of spur gears havir 0°…

A: given,p=15 kwNm=1200 rpmNc=300 rpmL=400 mm(σ)p=210 mpa(σ)G=140 mpanow , let face width ,b=10 mmand…

Q: The figure shows a pair of shaft-mounted spur gears having an 18-tooth pinion driving a 45- tooth…

A: Given data: The number of teeth on the pinion, t1 = 18. The number of teeth on the gear, t2 = 45.…

Q: Figure 1 shows a blower is driven by a 3-phase Brook Crompton motor via a Compound Gear Train having…

A: Given:To find:Speed required by motorPower required by motor

Q: A pair of steel gears have a design life of a million cycles. They have 20° full-depth teeth with a…

A: Pitch diameter , d=NPdd==208=2.5Velocity V=πdn12V=π X 2.5 X 200012V=1308 ft/minVelocity factor for…

Q: Two mating spur gears have 40 and 120 teeth respectively. The pinion rotates at 1200 rpm and…

A: Two mating spur gears have Z1 = 40 and Z2 = 120 teeth respectively. The pinion rotates at N1 = 1200…

Q: Assignment 1 A bevel gear receives a power from bevel pinion results in the shown forces. The forces…

A: 1 2

Q: A pair of gray iron and steel helical gears, having a helix angle of 15° with 20° full-depth teeth…

A: Answer: (a) Normal circular pitch: 0.4335 in (b) Normal diametral pitch: 7.2470 in (c) Axial pitch:…

Q: (b) Determine the safe power which can be transmitted by a pair of helical gears, 20° full depth,…

A: Gears are the two rings having teeth on it which are meshed together to transmit the power. They are…

Q: Figure below shours a portion of a pump that is gear-diven at uniform load and speed The 25 mm…

Q: 3. A double-threaded right-handed worm gear transmit 15-hp at 1150 rpm. The pitch of the worm is…

Q: gearing arrangement suitable for this

A: Given; A motor is running at; N= 1440 rev/minMotor power is given to run the motor is; P= 1.5…

Q: The figure shows a 16T 20° straight bevel pinion driving a 32 T gear and the location of the bearing…

A: Given data ;Power = 2 HpSpeed (N) = 200 rev/minr=2 inch

Q: 15KW and 1200r.p.m motor drives a compressor at 300r.p.m through a pair of spur gears having 20°…

Q: ExJA 20° straight-tooth bevel pinion having 14 teeth and a diametral pitch of 6 teeth/inch drives a…

Q: Problem 1-determine the maximum moment of the assembly. Hint: Obtain the moments for vertical and…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: A gearset has a module of 5 mm, a 20 degree pressure angle, and a 24-tooth cast iron spur pinion…

A: Given-Information: Module = 5 mmPressure angle = 20°Number of tooth on pinion(Zp)=24Rotational speed…

Concept explainers

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.

Question

A 15 kW and 1200 r.p.m. motor drives a compressor at 300 r.p.m. through a pair of spur gears having
20° stub teeth. The centre to centre distance between the shafts is 400 mm. The motor pinion is made
of forged steel having an allowable static stress as 210 MPa, while the gear is made of cast steel
having allowable static stress as 140 MPa. Assuming that the drive operates 8 to 10 hours per day
under light shock conditions, find from the standpoint of strength,
1. Module; 2. Face width and 3. Number of teeth and pitch circle diameter of each gear.
Check the gears thus designed from the consideration of wear. The surface endurance limit may be
taken as 700 MPa.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Design of Power Transmission Elements and Power Transmission Systems

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A pair of gray iron and steel helical gears, having a helix angle of 15° with 20° full-depth teeth are to transmit 10 hp at 1500 rpm of a 4-in pinion having a total number of 28teeth. The velocity ratio desired is about mw = 4. Find the (a) normal circular pitch, (b) normal diametral pitch, (c) axial pitch, and (d) dynamic load
A bevel gear receives a power from bevel pinion results in the shown forces. The forces are F = 7026.8 i - 3513.4j+ 215840.8 k . the bevel gear average diameter is 210 mm. the shaft is supported at bearing E and F and delivers the power to a flange coupling at end G. the shaft is made of steel 826 M 40 H&T having Sy = 650 MPa and Sult = 850 MPa. Determine the shaft diameter at its critical section and make a complete construction drawing. Fr= 3513.4 N F, = 7026.8 N. F= 21584.8 N 100 mm 200 mm 105 mm
A 35 kW motor running at 1200 rpm drives a compressor at 780 rpm. The arrangement is made through a 90° bevel gearing arrangement. The pressure angle of teeth is 14.5°. The allowable static stress for both pinion and gear are 85 MPa. Determine the number of teeth on the gear, face width, addendum, dedendum, outside diameter and slant height, thickness of tooth. Also check your design from the standpoint of wear. Take surface endurance limit as 690 MPa and modulus of elasticity as 89 kN/mm2.
The module and the number of teeth on the pinion of a spur gear are 12mm and 15teeth respectively.A power of 400kW is to be transmitted at 1700rpm of width.if the involute teeth are of standard proportions (addendum=m) with the pressure angle of 22.5° determine (A) torque due to power delivered (B) tangential load (C) teeth width (E)load on the bearings
The gears of a gear wheel with a module of 4 mm, width of 60 mm and number of 18 teeth were broken during operation. If the gear wheel is made of cast iron (GG-25), with what torque is it loaded? Given: Speed factor Kv= 1.25; force distribution factor K m = 1; operating factor K 0 = 1.5; For GG-25 σem= 55 N / mm 2 , K f = 2.
A spur pinion rotating at 20 rad/sec and having 20 teeth transmits 20 kW to a gear wheel. The pressure angle is 20° and module is 20mm. The reaction exerted by the pinion at the centre of thc shaft is
A spur gear reducer is to transmit 4 kW at 1500 rpm of the pinion of cast steel ( So=138 MPa). The gear is made from phosphor bronze (So=83 MPa). The velocity ratio is 3.5 to 1.0. Assume a pressure angle of 20°. Design the gears for strength only.
Q5: Select A suitable spline having a fit B for a gear to be mounted on a shaft with a diameter D= 60 mm. The gear transmits a torque of T=2.3 x 106 N.mm and has a hub length of L=100 mm.