A= 1200 mm?. Use Strain Energy Method 35 kN - 4m B 84 kN 4m 3m

Q: The forces as given below are applied as shown in the figure. F1=10 kN, F2=5 kN and F3=3 kN. The…

A: a)  -159.15 MPa(Compressive) , 35.80 MPa(shear stress) b) Principle stresses 7.686 MPa ,-166.836 MPa…

Q: Griven luteral os toain=2x1015 lenytudinal %3D train=5X105 Relermine bonson's reatio

A:

Q: The bending moment in a horizontally placed beam at distance x from one of the ends is given by the…

A: GIVEN DATA - A BENDING MOMENT EQUATION IS GIVEN WE HAVE TO FIND AT WHAT VALUE OF x SHEAR FORCE WILL…

Q: 5 kN.m is applied to the purlin in a plane at an angle of 30 deg to the vertical y axis. If the…

A: givenM=5000Nm, θ=30οMx=5000×103 cos30ο=4.4×105 N-mmMy=5000×103sin 30ο=2.2×105 N-mm

Q: 5 kN P 60 40 20 Al diniensions in mm Fat

A: The given section is, For the given section calculate the moment the fixed joint is,…

Q: = A solid steel cylinder with diameter of 40 mm and a shear modulus of G = = 75 GPa has fixed ends.…

A: Step 1: Step 2: solution is given above Step 3: Step 4:

Q: Mohr's circle for an element is shown, each grid is 5 MPa square. A rotated plane through the…

A:

Q: Given a shear stress of Txy = 5000 psi and a shear modulus of G 1.15 x 107 psi, find the shear…

A:

Q: 10 KN 20 KN / m 5 KN / m A B SIMPLE STRESSES 5 KN / m D 5 KN / m F 50 KN-m E 3. Points C and D of…

A: Given DataP=10kNw1=5kN/mw2=20kN/m

Q: Find the longitudinal strain Change in length=0.45 mm Initial length=1000 mm

A: Given data : Initial length=L Change in length=∆L   To find : Strain

Q: For the given fig find the  longitudinal variation of the bending stress

A: Given ; The bending  moment varies from zero to 10 Nm along the length of the  beam from the centre…

Q: Problem: Figure shows a frame subjected to a load of 3.4 kN, find the resultant stress at A and B.

A:

Q: Find the lateral strain Poisson ratio=0.334 Longitudinal strain=0.00546

A:

Q: as -ja-A Find the approximate prime plane in dogreos for the state of st given in the figure. 45 MPa…

A:

Q: Figure 1. 40 kN 30 kN/m 20 KN B K A -2m+ K 2m Re RA Figure 1. 85 mmm 68 mm Section K-K

A:

Q: 1. The state of plain strain at a point in a body is given by = 800 x 10-6, y = 200 x 10-6, and yxy…

A:

Q: Find the lateral strain Poisson ratio=0.334 Longitudinal strain=0.00546

A: Given data : Poisson ratio μ=0.334 Longitudinal strain εL=0.0546   Required : Lateral strain

Q: Mohr's circle for an element is shown below. If each grid is 15 MPa then the maximum shear stress…

A: Mohr's circle is a two-dimensional graphical depiction of the Cauchy stress tensor transformation…

Q: Find the longitudinal strain Change in length=0.45 mm Initial length=1000 mm

A: Given :  change in length , δL = 0.45 mm initial length, L = 1000 mm To find : longitudinal strain…

Q: 2. For the dimensions provided below, what would be the expected strain at point A if the…

A: Length of the cantilever (a+b): a+b=8+2=10 inches.Point load (F) acting at a distance a from the…

Q: AB, CD and EF are steel rods having a diameter of 10 mm and BD is a rigid beam. Using the following…

A: Given:-x=1.2mID=6P=3*ID(KN)=3×6=18kNE=200GPad=10mm FREE BODY DIAGRAM:-

Q: A circular tube is subjected to torque T at itsends. The resulting maximum shear strain in the…

A:

Q: Calcuate Torsion and Bending From Point A to Point B and Point A to Point C. Draw a FBD from point A…

A: For the solution refer below images.Find F.B.D. and shear and bending diagrams for portions AB and…

Q: A structural member is subjected to a set of forces and moments. Each separately produces the stress…

A:

Q: 10 N 1omm Im lomm

A:

Q: Find the initial length of rod if strain value is 0.0003 and change in length value 0.3 mm

A: Given data : Change in length=∆L Strain=ε   Required : Initial length of rod

Q: p is equal to

A: Given: The maximum shear strain in the rod is p×10-3, then p is equal ?Where, Cylindrical rod of…

Q: When a force P of 750 N is applied to the pedal shown in the figure, find the diameter (mm) of this…

A:

Q: B. SOLVE FOR THE STRESS IN THE ROD IF ITS CROSS-SECTIONAL AREA 1S 2500mm^2. 1.5m P=25KN

A: Given A=2500mm2

Q: Find the strain Initial length=100 mm Change in length=0.567 mm

A:

Q: Find the strain Initial length=100 mm Change in length=0.567 mm

A: Given data : Initial length L=100 mm Change in length=0.567 mm   To find : Strain

Q: Find the strain Initial length=102.78 mm Change in length=0.004 mm

A:

Q: Q2 The internal bending moment in a beam with a cross sectional area shown in the figure is 500 a in…

A: Given,  M= 500 N-m, Now A1=(50+25+50)×25=3125 mm2and area A2=100×35= 3500 mm2 CG of area A1,  x1=0,…

Q: A planar stress element has the stress state: O₂ = 16 MPa, 0y = 44 MPa and Txy = 39 MPa. Through…

A:

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.