A 120 thick one-way RC slab is subjected to loads (wt. of slab is not included) as shown. Required: Check the adequacy of the slab against flexure only using USD-NSCP 2010. Use any method of analysis for indeterminate slab & Draw V & M diagram. Use: fy= 411 MPa; fc'=21 MPa; cc=29 mm. LL=2.2 KPa/DL = 5.1KPa 5.9m 21mmø REBARS at 220 mm O.C. 2m 22mmø REBARS at 120 mm O.C.

A 120 thick one-way RC slab is subjected to loads (wt. of slab is not included) as shown. Required: Check the adequacy of the slab against flexure only using USD-NSCP 2010. Use any method of analysis for indeterminate slab & Draw V & M diagram. Use: fy= 411 MPa; fc'=21 MPa; cc=29 mm. LL=2.2 KPa/DL = 5.1KPa 5.9m 21mmø REBARS at 220 mm O.C. 2m 22mmø REBARS at 120 mm O.C.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rectangular footing 2.1 m x 3.2 m x 0.37 m thick supports a 300 mm square column at its center. Column loads are service conditions: DL = 363 kN LL = 291 kN f'c = 21 MPa Fy = 415 MPa Concrete cover to the centroid of steel reinforcement = 100 mm Calculate the nominal punching shear stress in the slab. Write your final answer with 2 decimal places if the unit is MPa.
a rectangular footing 2.3 m x 3.3 m x 0.31 m thick supports a 300 mm square column at its center. column loads are service conditions:DL = 385 kN LL = 292 kN f'c = 21 MPa fy = 415 MPa Concrete cover to the centroid of steel reinforcement = 100 mm calculate the nominal punching shear stress in the slab. write your final answer with 2 decimal places if the unit is MPA.
60. If the loss of prestress is excessive resulting in tensile cracks, which method should be used? A. O Preloading method B. O Hollow method C. O Transparent method D. O Layered method
Please solve completely and give stepwise solution. ACI- 318 Question:2 A one-way slab is supporting a uniform service dead load (excluding self-weight) of 50 psf and a uniform service live load of 40 psf as shown in Fig. 02. It is required to; (a) Analyze the given slab for flexure. (b) Design the given slab for flexure. Use only # 4 bar for flexure. Take fe' = 3 ksi and fy = 40 ksi. 12" Slab 12.75' Figure 02.
these are the answers I only need solutions 1. f = 8.42 MPa 2. Mcr= 121.0 kN-m 3. fconc= 10.42 MPafsteel= 197.22 MPaf’steel= 104.30 MPa
ALLE A square lead slab of side 50 cm and thickness 10 cm is subjected to a shearing force (on its narrow fa of 9 x 104 N. The lower edge is riveted to the floor. How much will the upper edge be displaced? (Shear modulus of lead 5.6 x 109 N m²) (4) 1.6 cm (1) 0.16 mm (2) 1.6 mm (3) 0.16 cm
Question 8 A sample slab section view is shown below: *4 0 10" EW 30 Felt Joint El. See What should be the correct reinforcement configuration in plan view for this slab? What should be the correct reinforcement configuration in plan view for this slab? 10" 10" 10" 10"- #4 bars 10"- 10" 10" 10" #4 bars 10"- # 4 bars 10"-
30 A rectangular footing 2.3 m x 3.6 m x 0.38 m thick supports a 300 mm square column at its center. Column loads are service conditions: DL = 306 kN LL = 241 kN f’c = 21 MPa fy = 415 MPa Concrete cover to the centroid of steel reinforcement = 100 mm Calculate the nominal punching shear stress in the slab. Write your final answer with 2 decimal places if the unit is MPA.
Design a simply supported one- way slab with ln=4m. Let fy=276MPa, f’c=21MPa, db=10mm and Cc=20mma. Determine the thickness of the slabb. Determine the required reinforcement spacing and check the for minimum and maximum values set by NSCP.
Title: CRACK ANALYSIS OF BEAMS PROBLEM: Determine the crack width of the following given beams: Take Bh = 1.20, fy = 414 MPa and fc' = 28 MPa.