A 12-mm thick steel tire has a width of 110 mm and an internal diameter of 800 mm. It is heated and shrunk onto a steel wheel 800.50 mm in diameter. E = 200 GPA. Determine the tensile stress in the tire. Determine the compressive pressure between the tire and the wheel. If the tire has an allowable tensile stress of 124 MPa and is to resist a pressure of 1.50 MPa, determine its thickness.

A 12-mm thick steel tire has a width of 110 mm and an internal diameter of 800 mm. It is heated and shrunk onto a steel wheel 800.50 mm in diameter. E = 200 GPA. Determine the tensile stress in the tire. Determine the compressive pressure between the tire and the wheel. If the tire has an allowable tensile stress of 124 MPa and is to resist a pressure of 1.50 MPa, determine its thickness.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Situation 4: An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in Figure. Axial loads are applied at the positions indicated. Steel A = 550 mm² 10. Compute the axial stress at the bronze 11. Compute the axial stress at the aluminum 12. Compute the axial stress at the steel 60 KN 3.0 m Aluminum A = 400 mm² 2.0 m Bronze A = 220 mm² 20 KN 1.0 m 30 kN
A circular aluminum alloy [E = 70 GPa; a = 22.5 x 10-6/°C; v = 0.33] pipe has an outside diameter of 170 mm, a wall thickness of 12 mm, and a length of 4.5 m. The pipe supports a compressive load of 630 kN. After the temperature of the pipe drops 53°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer: (a) d = i AD= i mm mm
Part 2 * Your answer is incorrect. The z-component of momemt M will cause compression at A and B, and tension at C and D. The y-component of moment M will cause compression at A and D, and tension at B and C. The maximum tensile bending stress will occur at point C. Calculate the magnitude of the largest bending moment that can be applied so that the stress at corner C does not exceed 205 MPa. Answer: M- eTextbook and Media Save for Later Part 3 8.31E1 Answer: M-i The z-component of moment M will cause compression at A and B, and tension at C and D. The y-component of moment M will cause compression at A and D, and tension at B and C. The maximum compressive bending stress will occur at point A. Calculate the magnitude of the largest bending moment that can be applied so that the stress at corner A does not exceed 205 MPa. eTextbook and Media Save for Later Part 4 kN-m * Your answer is incorrect. kN-m Submit Answer Determine the maximum bending moment that can be applied to this cross…
Ques.
The cross section of the AB part of the welded pipe part given in the figure is a hollow pipe and the cross section of the BC part is a circle with a solid body. The inner diameter of the pipe section is 20mm and the outer diameter is 28mm, while the diameter of the full body part is 12mm. Determine the average normal stress at the D and E points accordingly.
The tank shown in the Figure below is fabricated from a 10-mm steel plate. If the internal pressure in the tank is 1.2 MPa, calculate the tangential stress in the tank in MPa? ... 400 mm 600 mm
Answer all.a.A mild steel flat of width b= 150 mm, thickness t = 20 mm and length L= 6000 mm carries an axial pull P = 300 kN. If modulus of elasticity of mild steel is 200 GPa and Poisson’s ratio is 0.25, calculate the change in length, width and thickness of the flat. B.A stepped bar made of brass is subjected to axial loads as shown in the below figure. Determine the total change in length of the bar. Take E =100 GPa.figure is attached C.A thin cylinder of external diameter 820 mm, length 3 m and wall thickness of 10 mm is subjected to an internal pressure of 2.5 N/mm2 . Determine the change in diameter and length. Take Young’s modulus = 2×105 N/mm2 and Poisson’s ratio = 0.25.
1. The assembly has the diameters and material makeup indicated. If it fits securely between its fixed supports when the temperature is T; = 70°F, determine the average normal stress in each material when the temperature reaches T2 = 130°F. 304 Stainless steel - 2014-T6 Aluminum -C 86100 Bronze A 12 in. 8 in. D C 4 in. -4 ft- 6 ft- 3 ft
A circular aluminum alloy [E = 70 GPa; a = 22.5 × 10-6/°C; v = 0.33] pipe has an outside diameter of 270 mm, a wall thickness of 13 mm, and a length of 5.5 m. The pipe supports a compressive load of 600 kN. After the temperature of the pipe drops 39°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer: (a) 8 = i AD = mm mm
Determine the maximum shearing stress developed in aluminum. Determine the maximum shearing stress developed in steel. Determine the maximum shearing stress developed in bronze.
From the given illustration below, the force acting on B is equal to 25 kN, on C = 20 kN, and on D = 30 kN. If the cross sectional area of the material is 600 sg.mm, what is the maximum stress in the bar? FINAL EXAM 一- A B FINAL EXAM
PROBLEM 2 A tri metallic bar is uniformly compressed by an axial force P-12KN applied through a rigid end plate The bar consists of a circular steel core surrounded by brass and copper tubes. The steel core has a diameter l0mm, the brass tube has an oute diameter of 15mm and the copper tube has an outer diameter of 20mm E for steel =210Gpa, E for brass = 100GPA and E for copper is 120GPA Calculate the compressive stress of each metal due to force P