A 1:1 Pulse Transformer (PT) is used to trigger the SCR in the adjacent figure. The SCR is rated at 1.5 kV, 250 A with = 250 mA, H=150 mA, and Gmax= 150 mA, Gmin= 100 mA. The SCR is connected to an inductive load, where L = 150 mH in series with a small resistance and the supply voltage is 200 V dc. The forward drops of all transistors/diodes and gate-cathode junction during ON state are 1.0 V. 1.0 Q 18V JU CR +200 V The minimum approximate volt-second rating of the pulse transformer suitable for triggering the SCR should be: (volt-second rating is the maximum of product of the voltage and the width of the pulse that may be applied)

A 1:1 Pulse Transformer (PT) is used to trigger the SCR in the adjacent figure. The SCR is rated at 1.5 kV, 250 A with = 250 mA, H=150 mA, and Gmax= 150 mA, Gmin= 100 mA. The SCR is connected to an inductive load, where L = 150 mH in series with a small resistance and the supply voltage is 200 V dc. The forward drops of all transistors/diodes and gate-cathode junction during ON state are 1.0 V. 1.0 Q 18V JU CR +200 V The minimum approximate volt-second rating of the pulse transformer suitable for triggering the SCR should be: (volt-second rating is the maximum of product of the voltage and the width of the pulse that may be applied)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

ex) A platinum coil has aresistance of and 3.767 3-1462at 4o°c at 100°c Lind Ro2 and a 2 40
Number 3
convert 1273 from octal to hex converter
For the clamper circuit shown below, Find and Plot the output waveforms and Check the essential condition of Clamper Circuit normal operation and compute the discharging time constant of this circuit. C 6 µF V. 5 Vin 3 KQ 2V -3 frequency=500 Hz
Q3/A- For the circuit shown in figure 3 draw the output voltage waveform across the SCR and the current wave form through the SCR for the input values of 5 V(45°), and 10 V(90°), and 8 V(135°). ▲ Vin RL 52.2ΚΩ R1 20kQ Vin D Σπ 2N3870 10 V 8 V 5 V -7 -r 1 70 I 90° 135° 45⁰ Figure 3 1 70 R2 2kQ DO
In Boost converter, if the supply voltage is 200 V and the Duty cycle is 50%, the output voltage will be 100 V 200 V 400 V None of the above O O O O
10. With a step-up transformer with a turns ratio of 6 and a primary voltage of 100V, what is the voltage on the secondary? 6 V 60 V 6000 V 600 V
Solve using current divider rule
Calculate the base current IB in uA when VCC=18V, VEE=-14V , RB=9881 ohm, RC=13962ohm, RE=10804ohm and B=108
İf the effective voltage value is 80 volts and the effective current value is 4A in the series RLC circuit in the figure, what is the capacitance of the capacitor?
Silicon diode and 1kΩ resistor are connected in series to the 5V DC source output. What is the current passing through the circuit?
Answer with full steps