a 10KN 100mm diameter plunger is applied on a 100 mm thick block. the shaering stress eveloped on the block /hat force is required to punch a 25 mm diameter hole in a plate that is 25 mm thick if the sh rength idevelop hollow steel tube with an inside diameter of 100 mm carry a tensile load of 400 KN. If the str limited to 120 MPa,

Q: No estimation is needed when all items are inspected

A: False statement Estimation is needed even if all the items are inspected as Estimation is used for…

Q: How to determine Z-value? How to determine D-value and TDT?

A: The Z-value is referred to calculation of the resistance of micro-organism at different temperatures…

Q: Describe surface grinding operation.

A: To achieve a smooth appearance, surface grinding is performed on flat surfaces. Grinding is indeed a…

Q: Please give the figure with correct label

A: Given that total surface area of cylinder in square feet is equal to it's total volume in cubic…

Q: What are short stacks?

A: The short stacks are the reciprocating engine exhaust system.

Q: Engineers may accept outside work without notifying their primary employer. True False

A: Brief concept- There are certain ethical codes of conduct according to which the work should be…

Q: 2. cos2xcos7xdx

A: Consider the given equation ∫cos2xcos7xdx Use the identity cosxcosy=12cosx+y+cosx-y…

Q: Please answer it asap thanks!! Q2ii. During the Defects Liability Period, the Contractor is still…

A: Defects liability period It is a fixed time period, starting from the date of practical completion,…

Q: What are the similarities and difference between the actual ASTM C143 standard and the procedure…

A: In ASTM C143, the test method includes the determination of the hydraulic cement concrete slump in…

Q: Discuss about Durability-Related Serviceability Limits

A: The limit state method accounts for the design of structure assuming that it has reached its state…

Q: Discuss in detail Kennedy and Lacey Theory? Write down all the design steps.

A:

Q: Q4: Prove that:

A:

Q: Present two separate summaries for making and curing cylinder and beam sample in accordance with…

A: Making Cylinder:- The moulds should be provided with two machined metal and end plates at least 25mm…

Q: Dewfine the term final completion?

A: During the closing process of the project, the final completion-also recognized as final approval is…

Q: Stability (one word): Blank 1 Determinacy (two-words); Blank 2 to the Blank 3 degree Blank 1 Blank 2…

A:

Q: Describe the Standard Model of Consolidation

A: The Standard Model of Consolidation is a geotechnical engineering model that was developed to…

Q: What is a sieve plate

A:

Q: Quick step by step RFP process for construction.

A: This question is related to the Computer aided drafting and design from Civil Engineering.

Q: The information shown in this attached document. This has been extracted from the Expert Panel…

A: The order of construction in civil projects can vary depending on the specific project and its…

Q: 6.2 THE FOLLOWING PROVISIONS IN A CONSTRUCTION CONTRACT ARE UNENFORCEABLE: CHECK ALL CORRECT…

A: UNENFORCEABLE  means the clause in a contract that cannot be legally upheld by lawIt means if one…

Q: Define The structural ultimate limit

A: In the limit state method a structure is designed for safety against collapse (for ultimate strength…

Q: Define the size of a concrete cube?

A: Cube test of concrete is one of the most important tests done on concrete. It is also known as a…

Q: (c) Determine the length of X and Y for the rectangular plate as shown in FIGURE Q1(b) if the area…

A: Area of rectangular plate, A = 2 m2.Perimeter of rectangular plate, P=2X+2Y = 500 cmIt is asked to…

Q: potential design fault in the structure of Citicorp building New York

A: Since the building's skeleton was compromised by the presence of stilts in the centre of each side,…

Q: Define the Hiley's formula ?

A: Hiley's formula to calculate the ultimate capacity of the pile is given by, Qup=ηHηbWHS+C2 Here, ηH…

Q: What is ASD method

A: Allowable Stress Design (ASD) It is also known as the service load design or working stress design…

Q: What are the types, and applications of geotextiles? How are geotextiles installed.

A:

Q: Q)What are the components of a 3D cement construction printer and a 3D metal printer?

A: The components of a 3D cement construction printer and a 3D metal printer are: 1.Extruders :…

Q: Define Boussinesq’s Method

A: The Stress Computation Method determines how the 3-dimensional stress distribution due to loading is…

Q: Please determine the second part

A: This question is related to the Traffic engineering from highway engineering to civil engineering.…

Q: Define Rooof Insulating..

A: Solution; Roof Insulating Insulation helps us to keep the desired temperature in the building. It…

Q: Evaluat the fllowing limits Lim X # a X>a X - a

A: Given values -  limx→a = x2+1 - a2+1x-a     ,    x ≠ a   Rule -  The above problem can be solved by…