A 100kW, 230V, shunt generator has an armature resistance and field resistance of 0.050 and 57.50. If the generator operates at rated voltage with SPL at 1.8kW, calculate the following: a) Machines' efficiency of conversion. b) At what load does the generator achieve maximum efficiency c) What is the value of this maximum efficiency?

A 100kW, 230V, shunt generator has an armature resistance and field resistance of 0.050 and 57.50. If the generator operates at rated voltage with SPL at 1.8kW, calculate the following: a) Machines' efficiency of conversion. b) At what load does the generator achieve maximum efficiency c) What is the value of this maximum efficiency?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The series field winding of a 170 kW, 250 V, 1450 rpm compound generator has a resistance of 0.00306 ohm. What will be the required resistance (in Ohm) of a noninductive diverter that will bypass 27 percent of the total armature current? "
The armature winding resistance of a long shunt connected DC generator is 0.4ohm, the resistances of the shunt and serial field windings are 125 ohms and 0.1 ohms, respectively. While the generator supplies 8KW of power to the load it feeds, which is the voltage it produces since the output voltage is 250V?
Two de generators each having linear characteristics that operate in parallel. One machine has a terminal voltage of 480V at no load and 220 V at a load current of 100A, while the other machine has a voltage of 470 V at no load and 200 V at 120 A. calculate the current in each generator and the bus bar voltage when the total load is 180 A. What is the kilowatt output of each machine under this condition?
Exercise 2 A shunt generator delivers 14A at 270V and the resistance of the shunt field and armature are 100 Q and 0.75 Q2, respectively. Calculate: i. The generated emf and the efficiency of this operating condition. ii. The generated emf if the shunt field impedance was triple and if it was double and the efficiency of these cases. iii. What emf could serve tha same active power of load but at load voltage of 240V and the efficiency in this case.
A long shunt compound dc generator supplies a current of 100 A at a voltahe of 220 V. If the resistance of the shunt field is 50 ohms, of the series field are respectively 0.05 ohm, 110 ohms and 0.06 ohm. If the overall efficiency of the above load is 88%, find the iron and friction losses.
Q2. A dc shut generator has a full load current of 50A at 200V. The stray losses are 500W andRsh= 50 ohm. If the full load efficiency is 80% find(1) Ra(2) Load current corresponding to maximum efficiency (3) Draw the variation of load current with efficiency (estimate)
50 KW, 240 V enduvi resistance of a generator with foreign excitation is 0.02 ohms. Generatorproduces rated voltage at rated load. Endüvi voltage and endüvi current at rated loadcalculate? If the output voltage is kept constant at 240V and the output power is reduced to 45 KWfind the enduvi tension necessary for this?
A three-phase star-connected alternator working at 1400 KVA,50 Hz, 2300 V, has an armature dc resistance of 0.15 2. Assume the ac resistance is 1.4 times the dc resistance. A field current of 75 A produces a short circuit current of 360 A and for the same field current the open circuit voltage is 1000 V. Determine a) Synchronous reactance of the machine b) Full load regulation at 0.9 leading c) Power angle a) b)
Choose True (V) or false( x) for the following : 4) Reluctance is a measure of "opposition" the magnetic circuit offers to the flux. 5) The rated output power (transformer rating) can be used to determine the turns ratio of the transformer. 6) With the increase in speed of a series DC motor, Both back emf as well as line current increase. 7) When an induction motor is stationary, the stator and rotor windings form the equivalent of a transformer. 8) Increasing the load current for DC Self-excited generator Shunt-Wound Generator will increase the terminal voltage. 9) In lap windings there are as many paths in parallel and used to produce high current, low voltage output. 10) In 3-pahse induction motor, if the rotor speed increases, the rate at which the rotating magnetic field cuts the rotor bars is increasing.
Q/ dc shunt generator 4 pole with 500 condcutor , wave running at speed 1000 r.p.m the resistance of armature and field are 0.02 , 55 ohm and delivering load 43.12kwatt at terminal voltage 220 volt, the iron losses is 750 watt 1-Torque developed by the prime mover .........and The torque developed by the armature ........... when running at 1000 r.p.m * 2-The load current ,,,,,,,,,,,,when the speed drops to 800 r.p.m. if If is unchanged ? * 3-Output of the prime motor…….kwatt * 4-Mechanical , electrical and overall efficiency …….. * 5-Flux per pole is......... wb *
4. What for brushes are employed in DC generator? 5. What is the function of armature in a DC generator? 6. What is the function of commutator in a DC machine in generator action. 7 Whieh diffe u0ad in